WAUCONDA, IL —
OSHA Inspection: HEIDT'S HOT ROD SHOP, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of HEIDT'S HOT ROD SHOP, INC. in 111 KERRY LANE, WAUCONDA, IL 60084 (NAICS 336330). OSHA activity number 309308641.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HEIDT'S HOT ROD SHOP, INC.
- Site address
- 111 KERRY LANE
- City
- WAUCONDA
- State
- IL
- ZIP
- 60084
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336330
- SIC code (legacy)
- 3714
- Employees
- 30
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
- Penalty
- Initial $1,125 · Current $788 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: (a) Model Shop, North End - The Atlas vertical band saw, Company Number 91, Serial Number 202092, used to cut metal, was not equipped with a magnetic restart or similar device. The saw was used on or about August 26, 2005. (b) Model Shop, North End - The Enco horizontal band saw, Serial Number 345540, Model Number 137-315, used to cut metal, was not equipped with a magnetic restart or similar device. The saw was used on or about August 26, 2005. (c) Shop, South End - The Wellsaw horizontal band saw, Serial Number 10898, Model Number 58B, used to cut metal, was not equipped with a magnetic restart or similar device. The saw was used on or about August 26, 2005. (d) Shop, South End - The Carolina horizontal band saw, Serial Number HD106470, Model Number HD10, was not equipped with a magnetic restart or similar device. This saw was used on or about August 26, 2005. Among other methods, one feasible and acceptable method to correct this hazard includes but not limited to the following: Conform to ANSI an American National Standards Institute for Metal Sawing Machines B11.10 - 2003, Section 6.11 in that the machine controls shall incorporate a type of drive motor starter that will disconnect the drive motor from the power source in the event of control voltage or power system failure. In accordance with 29 CFR 1903.19(d), abatement certification is required for this violation (using the CERTIFICATION OF CORRECTIVE ACTION WORKSHEET), and in addition, documentation demonstrating that abatement is complete must be included with your certification. This documentation may include, but not limited to, evidence of the purchase or repair of the equipment, photographic or video evidence of abatement, or other written records.
Recent events (2)
- — I (S) $787.50
- — Z (S) $1125.00
1910.147 C04 I
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
- Penalty
- Initial $1,125 · Current $788 Reduced
Recent events (2)
- — I (S) $787.50
- — Z (S) $1125.00
1910.147 C06 I
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
Recent events (2)
- — I (S)
- — Z (S)
1910.147 C07 I
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
Recent events (2)
- — I (S)
- — Z (S)
1910.178 L01 I
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
- Penalty
- Initial $900 · Current $630 Reduced
Recent events (2)
- — I (S) $630.00
- — Z (S) $900.00
1910.178 P01
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
- Penalty
- Initial $900 · Current $630 Reduced
Recent events (2)
- — I (S) $630.00
- — Z (S) $900.00
1910.212 A01
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
- Penalty
- Initial $1,125 · Current $788 Reduced
Recent events (2)
- — I (S) $787.50
- — Z (S) $1125.00
1910.219 F03
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
- Penalty
- Initial $1,125 · Current $788 Reduced
Recent events (2)
- — I (S) $787.50
- — Z (S) $1125.00
1910.303 B02
- Issued
- Oct 7, 2005
- Abate by
- Nov 9, 2005
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Heidt'S HOT ROD Shop, INC.
View Heidt'S HOT ROD Shop, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 336330)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 309308641.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.