NEWARK, NJ —
OSHA Inspection: METAL MANAGEMENT INC.
Accident-driven inspection · Safety discipline
At a glance
On , OSHA opened an accident-driven safety inspection of METAL MANAGEMENT INC. in 252-254 DOREMUS AVE, NEWARK, NJ 07105 (NAICS 423930). OSHA activity number 309351344.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- METAL MANAGEMENT INC.
- Site address
- 252-254 DOREMUS AVE
- City
- NEWARK
- State
- NJ
- ZIP
- 07105
- Mailing
- PO BOX 5157, NEWARK, NJ 07105
What kind of inspection was it?
- Inspection type
- Accident-driven (A)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Y
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 423930
- SIC code (legacy)
- 5093
- Employees
- 55
- Ownership type
- A
Citations
2 citations on file for this inspection.
5(a)(1)
- Issued
- May 16, 2006
- Abate by
- May 26, 2006
- Penalty
- Initial $5,000 · Current $5,000
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being struck with the load due to overloading/component failure: a) 252-254 Doremus ave. Newark NJ 07105 Employees were operating a Dico Crane Model H10 to dislodge materials that had jammed the mill. Violation disclosed on or about 11/24/2005. Among other methods, one feasible and acceptable method to correct this hazard is to acquire equipment designed for pulling such as a high capacity winch.ty
5(a)(1)
- Issued
- May 16, 2006
- Abate by
- May 26, 2006
- Penalty
- Initial $5,000 · Current $5,000
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard created by component failure: a) 252-254 Doremus ave. Newark NJ 07105 The employer permitted employees to operate Dico Crane Model H10 crane to lift loads without knowing the their weight. Violation disclosed on or about 11/24/2005. Among other methods, one feasible and acceptable method to correct this hazard is to comply with the requirements established by the manufacturer, such as but not limited to knowing the weight of the load being handled (p.7 Operating Manual). b) 252-254 Doremus ave. Newark NJ 07105 The employer allowed the Dico Crane Model H10 to be operated daily. The only maintenance performed was "grease the bearings every month or when needed", and rebuild the entire unit 1 x per year". Violation disclosed on or about 12/14/2005. Among other methods, one feasible and acceptable method to correct this hazard is to comply with the requirements established by the manufacturer with respect to maintenance and lubrication (Operating Manual).ng
More inspections at Metal Management INC.
View Metal Management INC.'s full OSHA safety record →
More inspections in this industry (NAICS 423930)
More inspections in NJ
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 309351344.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.