DURHAM, NC — 2006-04-07 00:00:00

OSHA Inspection: S & D TOOL AND DIE, INC. DBA S & D MACHINE AND TOO

Complaint inspection · Safety discipline

At a glance

On 2006-04-07 00:00:00, OSHA opened a complaint safety inspection of S & D TOOL AND DIE, INC. DBA S & D MACHINE AND TOO in 1404 OLD OXFORD ROAD, DURHAM, NC 27704 (NAICS 332710). OSHA activity number 309738037.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch S & D Tool and DIE, INC. DBA S & D Machine and TOO — free Get an email when a new federal OSHA severe-injury report for S & D Tool and DIE, INC. DBA S & D Machine and TOO is published. One employer, no account, unsubscribe in one click.

Where did this inspection happen?

Establishment: S & D TOOL AND DIE, INC. DBA S & D MACHINE AND TOO
Site address: 1404 OLD OXFORD ROAD
City: DURHAM
State: NC
ZIP: 27704

What kind of inspection was it?

Inspection type: Complaint (B)
Scope: Partial (B)
Discipline: Safety
Advance notice: No
Union status: N

When did the case open and close?

Opened: 2006-04-07 00:00:00
Closing conference: 2006-04-07 00:00:00
Case closed: 2006-08-23 00:00:00
Last modified: 2006-09-19 00:00:00
Data loaded: 2011-10-14 16:38:47

Establishment context

NAICS code: 332710
SIC code (legacy): 3599
Employees: 22
Ownership type: A
Industry flags: Manufacturing safety.

Citations

13 citations on file for this inspection.

95012901

Serious 1 instance 2 exposed

Issued: May 12, 2006
Abate by: May 17, 2006
Penalty: Initial $700 · Current $700

General-duty citation text

North Carolina General Statute 95-129(1) of the Occupational Safety and
Health Act of North Carolina:  The
employer did not furnish each of his employees conditions of employment
and a place of employment free from
recognized hazards that were causing or likely to cause death or serious
physical harm to employees in that
employees were exposed to throw against, struck by and crushed by Roll
Over Protection System (ROPS)
hazard during tipover:
a)establishment, outside loading/unloading area - where the operator of a
Caterpillar Model CAT
T40B, S/N 274435, forklift was not wearing the installed seat belts during
operation.
One feasible and acceptable abatement method to correct this hazard is to
have operators fasten
the installed seat belt when operating the equipment.
(Reference: American Society of Mechanical Engineers, Safety Standard for
Low Lift and High
Lift Trucks (forklifts), ASME B56-1-1993, Paragraph 5.3.19: An active
operator protection
device or system, when provided, shall be used.

1910.212 A01

Serious 3 instances 2 exposed

Issued: May 12, 2006
Abate by: May 17, 2006
Penalty: Initial $500 · Current $500

1910.212 A03 II

Serious 3 instances 1 exposed

Issued: May 12, 2006
Abate by: May 17, 2006

1910.22 D01

Other-than-serious 1 instance 18 exposed

Issued: May 12, 2006
Abate by: May 17, 2006

1910.132 D02

Other-than-serious 1 instance 18 exposed

Issued: May 12, 2006
Abate by: Jun 29, 2006