LAKE BLUFF, IL —
OSHA Inspection: PROFILE PLASTICS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of PROFILE PLASTICS, INC. in 65 S. WAUKEGAN ROAD, LAKE BLUFF, IL 60044 (NAICS 326199). OSHA activity number 309882017.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PROFILE PLASTICS, INC.
- Site address
- 65 S. WAUKEGAN ROAD
- City
- LAKE BLUFF
- State
- IL
- ZIP
- 60044
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 326199
- SIC code (legacy)
- 3089
- Employees
- 75
- Ownership type
- A
Citations
8 citations on file for this inspection.
5(a)(1)
- Issued
- Apr 18, 2006
- Abate by
- Apr 21, 2006
- Penalty
- Initial $1,125 · Current $1,125
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the rotating blade: (a) Maintenance/Tool Room, East End - The Dayton horizontal band saw, used to cut metal parts, was not equipped with a magnetic restart or equivalent device. The saw was last used on or about on or about March 8, 2006. Among other methods, one feasible and acceptable method to correct this hazard includes but not limited to the following ANSI a American National Standard Institute for Safety Requirements for Metal Sawing Machines ANSI B11.10 - 2003, Section 6.11. All machine controls shall incorporate a type of drive motor starter that will disconnect the drive motor from the power source in the event of control voltage or power system failure. A separate starting operation shall be performed to restart the motor when power conditions are restored to normal. No abatement certification or documentation is required for this item.
1910.176 B
- Issued
- Apr 18, 2006
- Abate by
- Apr 21, 2006
- Penalty
- Initial $900 · Current $900
1910.332 B01
- Issued
- Apr 18, 2006
- Abate by
- Jun 5, 2006
- Penalty
- Initial $1,125 · Current $1,125
1910.333 B02 I
- Issued
- Apr 18, 2006
- Abate by
- May 23, 2006
1910.335 A01 I
- Issued
- Apr 18, 2006
- Abate by
- May 23, 2006
- Penalty
- Initial $1,125 · Current $1,125
1910.147 C04 I
- Issued
- Apr 18, 2006
- Abate by
- Apr 21, 2006
- Penalty
- Initial $3,000 · Current $3,000
1910.147 C06 I
- Issued
- Apr 18, 2006
- Abate by
- Jun 5, 2006
1910.305 G02 III
- Issued
- Apr 18, 2006
- Abate by
- Apr 21, 2006
More inspections at Profile Plastics, INC.
View Profile Plastics, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 326199)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 309882017.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.