SHELBY, NC —
OSHA Inspection: SEAL WIRE COMPANY
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SEAL WIRE COMPANY in 658 WASHBURN SWITCH ROAD, SHELBY, NC 28150 (NAICS 331421). OSHA activity number 310039680.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SEAL WIRE COMPANY
- Site address
- 658 WASHBURN SWITCH ROAD
- City
- SHELBY
- State
- NC
- ZIP
- 28150
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 331421
- SIC code (legacy)
- 3351
- Employees
- 18
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
22 citations on file for this inspection.
95012901
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: a)facility wide -- underhung fixed and bottom running hoists were not load tested prior to being placed into initial service. Reference: ASME B30.11-1998, section 11-2.2 Testing, paragraph 11-2.2.2 Load Test. New, reinstalled, altered, repaired, and modified equipment should be tested prior to initial use as determined by a qualified person. NOTE:Among other feasible methods of abatement, one feasible and acceptable method to abate this hazard is to load test all overhead lifting devices as per ASME B30.11-1998.
95012901
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: a)facility wide -- underhung fixed and bottom running hoists were not frequently inspected. Reference: ASME B30.11-1998, section 11-2.1 Inspection, paragraph 11-2.1.2 Frequent Inspection, Frequent inspections shall be performed at intervals defined in paragraph 11-2.1.1(b)(1) monthly and shall include observations during operation. NOTE:Among other feasible methods of abatement, one feasible and acceptable method to abate this hazard is to inspect all overhead lifting devices as per ASME B30.11-1998.
95012901
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: a)facility wide -- underhung fixed and bottom running hoists were not periodically inspected. Reference: ASME B30.11-1998, section 11-2.1 Inspection, paragraph 11-2.1.3 Periodic Inspection, Periodic inspections shall be performed by an appointed person making records of apparent external conditions to provide the basis for a continuing evaluation at intervals defined in paragraph 11-2.1.1(b)(2), (annually). NOTE:Among other feasible methods of abatement, one feasible and acceptable method to abate this hazard is to inspect all overhead lifting devices as per ASME B30.11-1998.2),
1910.213 H01
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
- Penalty
- Initial $100 · Current $100
1910.215 B09
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
- Penalty
- Initial $100 · Current $100
1910.215 A04
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.215 D01
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.303 B02
- Issued
- Nov 22, 2006
- Abate by
- Nov 28, 2006
- Penalty
- Initial $100 · Current $100
1910.304 F05 V
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
- Penalty
- Initial $100 · Current $100
1910.22 A01
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.22 D01
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.157 C01
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.157 D02
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.179 J02 III
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.179 J02 IV
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.179 N01
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.179 N04 I
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.184 I09 III
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.242 A
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.303 F
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.304 E01 IV
- Issued
- Nov 22, 2006
- Abate by
- Dec 19, 2006
1910.305 G02 III
- Issued
- Nov 22, 2006
- Abate by
- Nov 28, 2006
More inspections at Seal Wire Company
View Seal Wire Company's full OSHA safety record →
More inspections in this industry (NAICS 331421)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 310039680.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.