Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: CENEX

Planned inspection · Safety discipline

On , OSHA opened a planned safety inspection of CENEX in 215 CENTRAL AVENUE EAST, MINOT, ND 58701 (NAICS 811111). OSHA activity number 310558556.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Cenex — free Get an email when a new federal OSHA severe-injury report for Cenex is published. One employer, no account, unsubscribe in one click.
Establishment
CENEX
Site address
215 CENTRAL AVENUE EAST
City
MINOT
State
ND
ZIP
58701
Mailing
215 CENTRAL AVENUE EAST, MINOT, ND 58701
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
N
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
811111
SIC code (legacy)
7538
Employees
54
Ownership type
A

1 citation on file for this inspection.

5(a)(1)

Serious Gravity 03 4 instances 4 exposed
Issued
Dec 14, 2006
Abate by
Jan 2, 2007
Penalty
Initial $1,750 · Current $875 Reduced
Section 5(a)(1) of the Occupational Safety and Health Act of 1970:  The
employer did not
furnish employment and a place of employment which were free from
recognized hazards that
were causing or likely to cause death or serious physical harm to
employees in that employees
were exposed to potential crushing hazards from falling loads and/or lift
parts:
(a) Service bay area, for employees utilizing a Forward 12000 #89011349
4-post lift and
a Forward 12000 #89011348 4-post lift where the single-point safety latch
mechanisms
were wrapped with inner tube and insulation foam materials with potential
to affect the
latching capability of the lifts.
(b) Service bay area, for employees utilizing the Forward 4-post, ALM
2-post and
Nussbau 2-post automotive lifts where the ALM manual, Lifting Point Guide
and Lifting-
it-Right documents were not maintained.
(c) Service bay area, for employees utilizing the Forward 4-post, ALM
2-post and
Nussbau 2-post automotive lifts where annual inspections of the lift were
not performed
in accordance with ANSI/ALI ALOIM documents.
(d) Service bay area, for employees utilizing the Forward 4-post, ALM
2-post and
Nussbau 2-post automotive lifts where annual training relating to the lift
operations was
not performed in accordance with ANSI/ALI ALOIM documents.
Abatement Note:
Among other methods, one feasible and acceptable method of abatement would
be to
follow the requirements of ANSI/ALI ALOIM and/or ANSI B153.1 which
includes,
among other requirements, the following:
1.Institute a preventive maintenance program according to the
manufacturer's
specifications.
2.Provide training to employees on proper use and care of the lifts.
3.Ensure all lifts are rated and marked with their load capacity.
4.Schedule and complete all periodic and annual inspections.
Abatement Note:  Abatement certification is required for this item (see
enclosed "Sample
Abatement Certification Letter").tion
Recent events (2)
  • — I (S) $875.00
  • — Z (S) $1750.00

View Cenex's full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 310558556.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.