MARION, NC —
OSHA Inspection: METAL INDUSTRIES, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of METAL INDUSTRIES, INC. in 5643 US 70 WEST, MARION, NC 28752 (NAICS 332813). OSHA activity number 310667357.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- METAL INDUSTRIES, INC.
- Site address
- 5643 US 70 WEST
- City
- MARION
- State
- NC
- ZIP
- 28752
- Mailing
- PO BOX 1210, MARION, NC 28752
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332813
- SIC code (legacy)
- 3471
- Employees
- 25
- Ownership type
- A
- Industry flags
- Manufacturing health.
Citations
12 citations on file for this inspection.
95012901
- Issued
- Dec 13, 2006
- Abate by
- Feb 1, 2007
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to fall or struck by hazards: (a) Facility, silver-tin line #10 - Underhung crane system was not load tested as required. REF: ANSI B30.16-2, Section 16-2.2, Paragraph 16-2.2.2 (b) Electric Powered or Air Powered Hoists (1)Complete new hoists shall be dynamically load tested by the manufacturer as specified in paragraphs 16-2.2.1(b)(1) and (2) with a load test not less than 125 of the rated load, except that if testing cannot be performed by the manufacturer, the user shall be notified and the load test shall be accomplished at another location or job site, by or under the direction of a designated person prior to the hoist being placed into service. (The user is testing the complete structure wether or not the hoist was tested by the manufacturer.) (c) The person conducting the load test shall prepare a written report of the load sustained during the test and the operations performed during the test. Reports must be placed on file. NOTE: Among other methods, one feasible and acceptable method to correct this hazard is to load test the underhung hoists as required and maintain records of the load tests.
95012901
- Issued
- Dec 13, 2006
- Abate by
- Feb 1, 2007
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: (a) Facility, plating lines #1-#10: Ten underhung monorail crane systems with one hoist each were not inspected periodically, (annually). REF:ANSI B30.11-1998, Chapter 11-2, Paragraph 11-2.1.3 (a)Periodic inspections shall be performed at intervals defined in para. 11-2.1.1(b)(2): Visual inspection by an appointed person making records of apparent external conditions to provide the basis for a continuing evaluation, as follows: normal service, equipment in place -- annually. (c)A qualified person shall examine any deficiencies found during the inspection to determine whether conditions found constitute a hazard, require disassembly for further inspection, or require replacement. NOTE: Among other methods, one feasible and acceptable abatement method to correct this hazard is to conduct periodic inspections (annual) on the monorail crane systems per the requirements of section 11-2.1.3 of ANSI B30-11-1998.
1910.304 F04
- Issued
- Dec 13, 2006
- Abate by
- Dec 18, 2006
- Penalty
- Initial $100 · Current $100
1910.305 B01
- Issued
- Dec 13, 2006
- Abate by
- Jan 10, 2007
- Penalty
- Initial $100 · Current $100
1910.22 D01
- Issued
- Dec 13, 2006
- Abate by
- Jan 10, 2007
1910.24 H
- Issued
- Dec 13, 2006
- Abate by
- Feb 1, 2007
1910.134 C02 I
- Issued
- Dec 13, 2006
- Abate by
- Jan 10, 2007
1910.157 C01
- Issued
- Dec 13, 2006
- Abate by
- Dec 18, 2006
1910.215 A04
- Issued
- Dec 13, 2006
- Abate by
- Feb 1, 2007
1910.303 F
- Issued
- Dec 13, 2006
- Abate by
- Jun 18, 2007
1910.303 G01 I
- Issued
- Dec 13, 2006
- Abate by
- Feb 1, 2007
1910.305 G02 III
- Issued
- Dec 13, 2006
- Abate by
- Dec 18, 2006
More inspections at Metal Industries, INC.
View Metal Industries, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332813)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 310667357.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.