BILLINGS, MT —
OSHA Inspection: DENNY MENHOLT FRONTIER CHEVROLET - HUMMER
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of DENNY MENHOLT FRONTIER CHEVROLET - HUMMER in 3000 KING AVE. WEST, BILLINGS, MT 59102 (NAICS 811198). OSHA activity number 311221170.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- DENNY MENHOLT FRONTIER CHEVROLET - HUMMER
- Site address
- 3000 KING AVE. WEST
- City
- BILLINGS
- State
- MT
- ZIP
- 59102
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 811198
- SIC code (legacy)
- 7539
- Employees
- 150
- Ownership type
- A
Citations
4 citations on file for this inspection.
5(a)(1)
- Issued
- Mar 9, 2010
- Abate by
- Mar 15, 2010
- Penalty
- Initial $3,500 · Current $3,500
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or likely to cause death or serious physical harm to his employees in that employees were exposed to: (a) Auto repair shop: On or about December 18, 2009 and at times prior thereto, employees were exposed to a struck by and crushing hazard while elevating vehicles using Rotary lifts with non-functioning locks on the lifting arms. (b) Auto repair shop: On or about December 18, 2009 and at times prior thereto, employees were exposed to a struck by and crushing hazard while elevating vehicles using Rotary lifts with missing or broken bolts in the lifting arm extensions. (c) Auto repair shop: On or about December 18, 2009 and at times prior thereto, employees exposed to a struck by and crushing hazard while elevating vehicles using an un-named 4 post auto lift with damaged ramps/chocks. (d) Auto repair shop: On or about December 18, 2009 and at times prior thereto, employees exposed to a crushing hazard while elevating vehicles using Rotary lift #16 with a damaged hydraulic reservoir tank. Abatement Note: Among other methods, one feasible and acceptable method to correct the hazards noted is to follow the requirements in ANSI/ALI ALOIM 2008 which include, among other requirements, the following: 1. Institute a preventive maintenance program according to the manufacturer's specifications. 2. Provide training to employees on proper use and care of the lifts. 3. Schedule and complete all periodic and annual inspections.
1910.215 A04
- Issued
- Mar 9, 2010
- Abate by
- Mar 15, 2010
- Penalty
- Initial $1,050 · Current $1,050
1910.215 B09
- Issued
- Mar 9, 2010
- Abate by
- Mar 15, 2010
1910.253 B02 IV
- Issued
- Mar 9, 2010
- Abate by
- Mar 15, 2010
- Penalty
- Initial $1,400 · Current $1,400
More inspections at Denny Menholt Frontier Chevrolet - Hummer
View Denny Menholt Frontier Chevrolet - Hummer's full OSHA safety record →
More inspections in this industry (NAICS 811198)
More inspections in MT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 311221170.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.