MURPHY, NC —
OSHA Inspection: SIOUX TOOLS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SIOUX TOOLS, INC. in 250 SNAP-ON DRIVE, MURPHY, NC 28906 (NAICS 332212). OSHA activity number 311339261.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Sioux Tools, INC. — free
Get an email when a new federal OSHA severe-injury report for Sioux Tools, INC. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- SIOUX TOOLS, INC.
- Site address
- 250 SNAP-ON DRIVE
- City
- MURPHY
- State
- NC
- ZIP
- 28906
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332212
- SIC code (legacy)
- 3423
- Employees
- 181
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
18 citations on file for this inspection.
95012901
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: a)Heat Treat area -- an initial inspections were not performed on two 1/4 ton Coffing jib hoists and a TMM 300 pound hoist (cranes) prior to their being placed into operation. b)Maintenance area -- a 1/2 ton floor crane and a 1 ton A-Frame hoist (crane) was not inspected prior to being placed into operation. c)Scrap Dock area -- a 1/2 ton Hercules floor crane was not inspected prior to being placed into operation. Reference:ANSI B30.11 - 1998, Chapter 11-2, Section 11-2.1, Paragraph 11-2.1.1(a). Prior to initial use all new, altered, or modified hoists (cranes) shall be inspected. NOTE:Among other methods of abatement, one feasible and acceptable method to correct this hazard is to have all overhead hoists (cranes) load tested.)
Recent events (2)
- — I (S) $100.00
- — Z (S) $100.00
1910.179 H04
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (S)
- — Z (S)
1910.179 J02 III
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (S)
- — Z (S)
1910.179 J02 IV
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (S)
- — Z (S)
1910.179 N04 I
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (S)
- — Z (S)
95012901
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: a)Heat Treat area -- load tests were not performed on two 1/4 ton Coffing jib hoists and a TMM 300 pound hoist (cranes) prior to their being placed into operation. b)Maintenance area -- a 1/2 ton floor crane and a 1 ton A-Frame hoist (crane) were not load tested prior to being placed into operation. c)Scrap Dock area -- a 1/2 ton Hercules floor crane was not load tested prior to being placed into operation. Reference:ANSI B30.11 - 1998, Chapter 11-2, Section 11-2.2, Paragraph 11-2.2.2.1(a). Prior to initial use all new, altered, or modified hoists (cranes) shall be load tested. NOTE:Among other methods of abatement, one feasible and acceptable method to correct this hazard is to have all overhead hoists (cranes) load tested.)
Recent events (2)
- — I (S) $100.00
- — Z (S) $100.00
95012901
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
- Penalty
- Initial $100 · Current $100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: a) Facility wide -- Dated inspection reports or comparable records of critical items such as hoisting machinery, sheaves, ropes, wheels, and other lifting devices, as required in ANSI B30.11-1998, Chapter 11-2, Section 11-2.1, Paragraph 11-2.1.1(b)(2), shall be maintained. Reference:ANSI B30.11-1998, Chapter 11-2, Section 11-2.1, Paragraph 11-2.1.5 NOTE:Among other methods of abatement of this violation, one feasible and acceptable method to abate this violation is to inspect all overhead hoists and hoisting machinery and maintain the inspection records where they are available to appointed personnel.
Recent events (2)
- — I (S) $100.00
- — Z (S) $100.00
1910.212 A03 II
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
- Penalty
- Initial $250 · Current $250
Recent events (2)
- — I (S) $250.00
- — Z (S) $250.00
1910.215 A02
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.215 D03
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.303 B02
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.304 B03 IIC3
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.304 B03 IIC4
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.304 B03 IIC6
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.305 A01 I
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.305 B02 I
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.305 G02 II
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
1910.305 J01 I
- Issued
- Feb 1, 2008
- Abate by
- Mar 20, 2008
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Sioux Tools, INC.
Jan 3, 2008
MURPHY, NC
Apr 7, 1999
VERMILLION, SD
Nov 24, 1997
SIOUX CITY, IA
Aug 31, 1995
SIOUX CITY, IA
Jan 5, 1990
LE MARS, IA
View Sioux Tools, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332212)
Jun 16, 2026
111419 - National Flooring Equipment LLC · MINNEAPOLIS, MN
Mar 30, 2026
160825 - American Striking Tool, INC. · WILMINGTON, NC
Jun 25, 2025
109378 - Thexton Manufacturing Company · MINNEAPOLIS, MN
Dec 3, 2024
108508 - Bicycle Tools INC DBA Park Tool CO · SAINT PAUL, MN
Oct 9, 2024
108240 - Northern Engineering and Manufacturing INC · ZIMMERMAN, MN
More inspections in NC
Jul 16, 2026
161563 - CSP Innovations North Carolina, INC. · LENOIR, NC
Jul 15, 2026
161557 - Union Electric Membership Corporation · LAKE PARK, NC
Jul 15, 2026
161554 - SE Board, INC · HIGH POINT, NC
Jul 15, 2026
161553 - Quality Arbor Services INC. · LAKE PARK, NC
Jul 15, 2026
161552 - EDC, INC. · KERNERSVILLE, NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 311339261.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.