BROOKINGS, SD —
OSHA Inspection: MTR TECHNOLOGIES
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of MTR TECHNOLOGIES in 201 32ND AVENUE, BROOKINGS, SD 57006 (NAICS 334419). OSHA activity number 311632632.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MTR TECHNOLOGIES
- Site address
- 201 32ND AVENUE
- City
- BROOKINGS
- State
- SD
- ZIP
- 57006
- Mailing
- 201 32ND AVENUE, BROOKINGS, SD 57006
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 334419
- SIC code (legacy)
- 3679
- Employees
- 47
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- Mar 5, 2008
- Abate by
- Mar 10, 2008
- Penalty
- Initial $625 · Current $625
Recent events (2)
- — Z (S) $625.00
- — I (S) $625.00
1910.212 A01
- Issued
- Mar 5, 2008
- Abate by
- Mar 10, 2008
Recent events (2)
- — Z (S)
- — I (S)
5(a)(1)
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
- Penalty
- Initial $1,250 · Current $1,250
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to crushing and/or struck-by hazards from moving machinery: (a) At MTR Technologies, where the Milltronic SL14/6 CNC turning lathe, serial #8491, was not equipped with a door interlock device exposing employees to the potential hazard of being struck by parts being expelled from the turning lathe or being caught in the moving machinery inside the turning lathe by opening the lathe door during the machine operating cycle. Among other methods, one feasible and acceptable abatement method to correct this hazard is to install a door interlock device on the Milltronic SL14/6 CNC turning lathe, serial #8491, as required by ANSI B11.22-2002 Safety Requirements for Turning Centers and Automatic, Numerically Controlled Turning Machines, paragraphs 6.21 Safeguarding and 6.21.1.2 Automatic Mode which states: 1. Paragraph 6.21: Machines shall be safeguarded wherever practical by fixed or interlocked moveable guards. 2. Paragraph 6.21.1.2: Machine operation shall only be possible when the guards are closed and the safeguarding (protective) devices are active. If it is possible, in this mode, to open an interlocked moveable guard, the hazardous movements shall cease and be inhibited. Abatement Note: Abatement certification is required for this item (see enclosed "Sample Abatement Certification Letter").tion
Recent events (2)
- — I (S) $1250.00
- — Z (S) $1250.00
1910.134 C01
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
- Penalty
- Initial $750
Recent events (2)
- — I (O)
- — Z (S) $750.00
1910.134 E01
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
Recent events (2)
- — I (O)
- — Z (S)
1910.134 F01
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
Recent events (2)
- — I (O)
- — Z (S)
1910.134 K01
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
Recent events (2)
- — I (O)
- — Z (S)
1910.212 A01
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
- Penalty
- Initial $750 · Current $750
Recent events (2)
- — I (S) $750.00
- — Z (S) $750.00
1904.29 A
- Issued
- Feb 6, 2008
- Abate by
- Mar 10, 2008
- Penalty
- Initial $500 · Current $250 Reduced
Recent events (2)
- — I (O) $250.00
- — Z (O) $500.00
More inspections in this industry (NAICS 334419)
More inspections in SD
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 311632632.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.