LAS VEGAS, NV —
OSHA Inspection: LM CONSTRUCTION CO., LLC
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of LM CONSTRUCTION CO., LLC in 6550 SOUTH BUFFALO, LAS VEGAS, NV 89113 (NAICS 238130). OSHA activity number 311637359.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- LM CONSTRUCTION CO., LLC
- Site address
- 6550 SOUTH BUFFALO
- City
- LAS VEGAS
- State
- NV
- ZIP
- 89113
- Mailing
- 6166 SOUTH SANDHILL ROAD, SUITE A, LAS VEGAS, NV 89120
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- SIC code (legacy)
- 1751
- Employees
- 2
- Ownership type
- A
- Industry flags
- Construction safety.
Citations
2 citations on file for this inspection.
618037501
- Issued
- Jan 31, 2008
- Abate by
- Feb 5, 2008
- Penalty
- Initial $1,500 · Current $300 Reduced
General-duty citation text
Nevada Revised Statute 618.375(1): The employer failed to furnish employment and a place of employment which was free from recognized hazards that were causing or were likely to cause death or serious physical harm to his employees: The employer failed to use safety devices and safeguards as follows: a.At the Arroyo jobsite, located at 6550 South Buffalo, two LM Construction employees were working from a JLG Gradall Personnel Platform, model # 9045 5052, serial #2003161147, performing framing duties. for approximately one hour. One of the employees stood on the top and middle guardrail to gain additional height, and was tied off to the mast of a JLG Material Handler; Model # 524/534D6/9/10/544, serial #JLGOP0210489, instead of using the engineered anchor points on the platform. The employees were exposed to possible serious injuries from falls approximately 25 feet to the ground below. Reference: ANSI A92.5 - 1992 Boom-Supported Elevating Work Platforms: Section 5.17.1 Operator Training: The user shall ensure that operators understand that safe operation is the operator's responsibility. The user shall ensure that operators are knowledgeable of, and observe, the safety rules and practices. Section 8.10.1 Personnel Footing: Personnel shall maintain a firm footing on the platform floor while working therein. Use of planks, ladders, or any other devices on the aerial platform for achieving additional height or reach shall be prohibited. Reference: JLG Gradall Personnel Platform Operators Manual: Section 6.0 Operation: The platform shall not be moved until the park brake is applied and the occupants are wearing a full body harness with a lanyard attached to designated point. One feasible means of abatement is to make sure that the proper personnel fall protection equipment required to do the job is provided and utilized correctly and personnel maintain firm footing at all times while using the Personnel Platform.
Recent events (2)
- — I (O) $300.00
- — Z (S) $1500.00
1926.503 A01
- Issued
- Jan 31, 2008
- Abate by
- Feb 5, 2008
Recent events (2)
- — I (O)
- — Z (S)
More inspections at LM Construction CO., LLC
View LM Construction CO., LLC's full OSHA safety record →
More inspections in this industry (NAICS 238130)
More inspections in NV
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 311637359.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.