SHERBURNE, NY —
OSHA Inspection: SHERBURNE METAL PRODUCTS, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of SHERBURNE METAL PRODUCTS, INC. in 40 SOUTH MAIN STREET, SHERBURNE, NY 13460 (NAICS 331421). OSHA activity number 312368053.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SHERBURNE METAL PRODUCTS, INC.
- Site address
- 40 SOUTH MAIN STREET
- City
- SHERBURNE
- State
- NY
- ZIP
- 13460
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 331421
- SIC code (legacy)
- 3351
- Employees
- 28
- Ownership type
- A
Citations
16 citations on file for this inspection.
5(a)(1)
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $1,000 · Current $600 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to THE HAZARD OF BEING STRUCK-BY falling loads: a)Chopper Area, on or about 3/26/09: 2-ton Gorbel hoist had splices in the pendent cable and the pendent controls were not labeled. b)Gerwin Machine, on or about 3/26/09: 3-ton CM hoist had splices in the pendent cable and the support structure was not marked with a load capacity rating. c)Synco Machine Area, on or about 3/26/09: 2-ton CM hoist had a missing safety latch on the load hook and the support structure was not marked with a load capacity rating. d)Bull Block Area, on or about 3/26/09: 3-ton CM hoist had the control pendent broken in half with tape holding it together. Among other methods, one feasible and method of abatement to correct these hazards is to conduct frequent and periodic inspections of lifting devices for wear, deterioration and malfunction, make the necessary repairs or replacements when needed, and post load capacity ratings as per ANSI B30.20-1993.
Recent events (2)
- — I (S) $600.00
- — Z (S) $1000.00
1910.132 A
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $1,250 · Current $750 Reduced
Recent events (2)
- — I (S) $750.00
- — Z (S) $1250.00
1910.132 H06
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
Recent events (2)
- — I (S)
- — Z (S)
1910.157 G01
- Issued
- Jul 16, 2009
- Abate by
- Aug 18, 2009
- Penalty
- Initial $1,250 · Current $750 Reduced
Recent events (4)
- — J $3600.00
- — Z $18000.00
- — I (S) $750.00
1910.179 L03 III
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $1,250 · Current $750 Reduced
Recent events (2)
- — I (S) $750.00
- — Z (S) $1250.00
1910.212 A03 II
- Issued
- Jul 16, 2009
- Abate by
- Aug 3, 2009
- Penalty
- Initial $1,250 · Current $750 Reduced
Recent events (4)
- — J $3600.00
- — Z $18000.00
- — I (S) $750.00
1910.212 A05
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $1,250 · Current $750 Reduced
Recent events (2)
- — I (S) $750.00
- — Z (S) $1250.00
1910.215 A04
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $1,000 · Current $600 Reduced
Recent events (2)
- — I (S) $600.00
- — Z (S) $1000.00
1910.215 B09
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
Recent events (2)
- — I (S)
- — Z (S)
1910.219 D01
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $750 · Current $450 Reduced
Recent events (2)
- — I (S) $450.00
- — Z (S) $750.00
1910.219 E01 I
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
Recent events (2)
- — I (S)
- — Z (S)
1910.304 G05
- Issued
- Jul 16, 2009
- Abate by
- Jul 21, 2009
- Penalty
- Initial $1,000 · Current $600 Reduced
Recent events (2)
- — I (S) $600.00
- — Z (S) $1000.00
1904.7 B03
- Issued
- Jul 16, 2009
- Abate by
- Jul 24, 2009
Recent events (2)
- — I (O)
- — Z (O)
1904.7 B05
- Issued
- Jul 16, 2009
- Abate by
- Jul 24, 2009
Recent events (2)
- — I (O)
- — Z (O)
1904.32 B02
- Issued
- Jul 16, 2009
- Abate by
- Jul 24, 2009
Recent events (2)
- — I (O)
- — Z (O)
1904.32 B06
- Issued
- Jul 16, 2009
- Abate by
- Jul 24, 2009
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Sherburne Metal Products, INC.
View Sherburne Metal Products, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 331421)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 312368053.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.