NEWTON, NC ·
OSHA Inspection: HAMCO MANUFACTURING AND DISTRIBUTING LLC
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of HAMCO MANUFACTURING AND DISTRIBUTING LLC in 1205 BURRIS ROAD, NEWTON, NC 28658 (NAICS 322130). OSHA activity number 312781560.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HAMCO MANUFACTURING AND DISTRIBUTING LLC
- Site address
- 1205 BURRIS ROAD
- City
- NEWTON
- State
- NC
- ZIP
- 28658
- Mailing
- PO BOX 810, NEWTON, NC 28658
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 322130
- SIC code (legacy)
- 2611
- Employees
- 70
- Ownership type
- Private (A)
- Industry flags
- Manufacturing health.
Citations
5 citations on file for this inspection.
95012901
- Issued
- Jan 5, 2009
- Abate by
- Feb 23, 2009
- Penalty
- Initial $525 · Current $525
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: (a) Facility, Warehousing area, rewinding machine - The rated load was not marked on the under the hook lifting device which was attached to one 3 ton hoist. (b) Facility, Converting area, Jenner Jahn Slittering machine #2 - The rated load was not marked on the under the hook lifting device which was attached to one 1 ton hoist. (c) Facility, Converting area, Jenner Jahn Slittering machine #3 - The rated load was not marked on the under the hook lifting device which was attached to one 1 ton hoist. REF: ANSI B30.20-1985, Chapter 20-1, Section 20-1.2 Markings, Paragraph 20-1.1.2 (a)Rated load marking. The rated load of the lifting device shall be marked on the structure where it is visible. (b)Identification. A nameplate or other permanent marking shall be affixed displaying the following information: (1)Manufacturer's name (2)Serial number (3)Lifter weigh, if over 100 lbs. (4)Rated load NOTE: Among other methods, one feasible and acceptable method to correct this hazard is to properly mark the rated load on the below the hook lifting device.
1910.178 N04
- Issued
- Jan 5, 2009
- Abate by
- Jan 30, 2009
- Penalty
- Initial $375 · Current $375
1910.147 C01
- Issued
- Jan 5, 2009
- Abate by
- Jan 30, 2009
1910.1200 E01
- Issued
- Jan 5, 2009
- Abate by
- Jan 30, 2009
1910.1200 F05 I
- Issued
- Jan 5, 2009
- Abate by
- Jan 30, 2009
More inspections at Hamco Manufacturing and Distributing LLC
View Hamco Manufacturing and Distributing LLC's full OSHA safety record →
More inspections in this industry (NAICS 322130)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 312781560.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.