RAPID CITY, SD —
OSHA Inspection: ADAMS MACHINING, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of ADAMS MACHINING, INC. in 2380 DEADWOOD AVENUE, RAPID CITY, SD 57702 (NAICS 332710). OSHA activity number 313767139.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ADAMS MACHINING, INC.
- Site address
- 2380 DEADWOOD AVENUE
- City
- RAPID CITY
- State
- SD
- ZIP
- 57702
- Mailing
- 2380 DEADWOOD AVENUE, RAPID CITY, SD 57702
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- SIC code (legacy)
- 3599
- Employees
- 25
- Ownership type
- A
Citations
2 citations on file for this inspection.
5(a)(1)
- Issued
- Oct 19, 2009
- Abate by
- Nov 23, 2009
- Penalty
- Initial $750 · Current $375 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to struck-by, crushing, and/or amputation hazards: (a) In the machining room for employees operating the TRAK TRL 1745 S CNC lathe, serial #023AU11744, where the CNC lathe was not equipped with a functional door interlock device exposing employees to the potential hazard of being struck by parts expelled from the turning lathe or being caught in the moving machinery inside the turning lathe by opening the lathe door during machine operating cycle. (b) In the machining room for employees operating the TRAK TRL2460SX CNC lathe, serial #084CV62226, where the CNC lathe was not equipped with a functional door interlock device exposing employees to the potential hazard of being struck by parts expelled from the turning lathe or being caught in the moving machinery inside the turning lathe by opening the lathe door during machine operating cycle. (c) In the machining room for employees operating the VMC 2040L CNC machine center, serial #N7070168, where the CNC machine center was not equipped with a functional door interlock device exposing employees to the potential hazard of being struck by parts expelled from the machine center or being caught in the moving machinery inside the machine center by opening the machine center door during machine operating cycle. Among other methods, one feasible and acceptable abatement method to correct this hazard is to install a door interlock device on the CNC lathes as required by ANSI B11.2-2002 Safety Requirements for Turning Centers Automatic Numerically Controlled Turning Machines, paragraphs 6.21 Safeguarding and 6.21.1.2 Automatic Mode which states: 1. Paragraph 6.21: Machines shall be safeguarded wherever practical by fixed or interlocked moveable guards. 2. Paragraph 6.21.1.2: Machine operation shall only be possible when the guards are closed and the safeguarding (protective) devices are active. If it is possible, in this mode, to open an interlocked moveable guard, the hazardous movement shall cease and be inhibited. Abatement Note: Abatement certification is required for this item (see enclosed "Sample Abatement Certification Letter").tion
Recent events (2)
- — I (S) $375.00
- — Z (S) $750.00
1910.212 A01
- Issued
- Oct 19, 2009
- Abate by
- Nov 23, 2009
- Penalty
- Initial $750 · Current $375 Reduced
Recent events (2)
- — I (S) $375.00
- — Z (S) $750.00
More inspections at Adams Machining, INC.
View Adams Machining, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in SD
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 313767139.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.