FRANKLIN PARK, IL ·
OSHA Inspection: KENSEN TOOL & DIE, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of KENSEN TOOL & DIE, INC. in 9200 PARK LANE, FRANKLIN PARK, IL 60131 (NAICS 333514). OSHA activity number 313893679.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- KENSEN TOOL & DIE, INC.
- Site address
- 9200 PARK LANE
- City
- FRANKLIN PARK
- State
- IL
- ZIP
- 60131
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333514
- SIC code (legacy)
- 3544
- Employees
- 16
- Ownership type
- Private (A)
Citations
11 citations on file for this inspection.
5(a)(1)
- Issued
- Dec 16, 2009
- Abate by
- Dec 21, 2009
- Penalty
- Initial $375 · Current $263 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the rotating blade when the power is restored and the saws start up: (a) Tool Room, South Wall - The Do All vertical band saw, Model Number 2013 used to cut metal parts, was not equipped with a magnetic restart or equivalent device. The saw was last used on or about November 12, 2009. (b) Tool Room, South Wall - The Kalamazoo horizontal band saw used to cut metal parts, was not equipped with a magnetic restart or equivalent device. The saw was last used on or about November 12, 2009. Among other methods, one feasible and acceptable method to correct this hazard includes but not limited to the following: Conform to ANSI the American National Standards Institute for Safety Requirements for Metal Sawing Machines, ANSI B11.10 - 2003, Section 6.11 which states" The machine controls shall incorporate a type of drive motor starter that will disconnect the drive motor from the power source in the event of the control voltage or power failure system failure" and National Fire Protection Association - NFPA 79 -2007, Section 7.5.3 "Upon restoration of the voltage or upon switching on the incoming supply, automatic or unintentional restarting of the machine shall be prevented when such a restart causes a hazardous condition." No abatement certification or documentation is required for this item.
Recent events (2)
- · I (S) $262.50
- · Z (S) $375.00
1910.147 C04 I
- Issued
- Dec 16, 2009
- Abate by
- Dec 21, 2009
- Penalty
- Initial $750 · Current $525 Reduced
Recent events (2)
- · I (S) $525.00
- · Z (S) $750.00
1910.147 C06 I
- Issued
- Dec 16, 2009
- Abate by
- Jan 21, 2010
1910.147 C07 IA
- Issued
- Dec 16, 2009
- Abate by
- Jan 21, 2010
1910.178 L01 I
- Issued
- Dec 16, 2009
- Abate by
- Jan 21, 2010
- Penalty
- Initial $225 · Current $158 Reduced
Recent events (2)
- · I (S) $157.50
- · Z (S) $225.00
1910.212 A01
- Issued
- Dec 16, 2009
- Abate by
- Jan 21, 2010
- Penalty
- Initial $300 · Current $210 Reduced
Recent events (2)
- · I (S) $210.00
- · Z (S) $300.00
1910.215 B05
- Issued
- Dec 16, 2009
- Abate by
- Dec 21, 2009
- Penalty
- Initial $255 · Current $179 Reduced
Recent events (2)
- · I (S) $178.50
- · Z (S) $255.00
1910.217 B07 VA
- Issued
- Dec 16, 2009
- Abate by
- Dec 21, 2009
- Penalty
- Initial $375 · Current $263 Reduced
Recent events (2)
- · I (S) $262.50
- · Z (S) $375.00
1910.217 C02 IA
- Issued
- Dec 16, 2009
- Abate by
- Dec 21, 2009
- Penalty
- Initial $375 · Current $263 Reduced
Recent events (2)
- · I (S) $262.50
- · Z (S) $375.00
1910.217 E01 I
- Issued
- Dec 16, 2009
- Abate by
- Jan 21, 2010
- Penalty
- Initial $375 · Current $263 Reduced
Recent events (2)
- · I (S) $262.50
- · Z (S) $375.00
1910.217 B07 III
- Issued
- Dec 16, 2009
- Abate by
- Jan 21, 2010
More inspections at Kensen Tool & DIE, INC.
View Kensen Tool & DIE, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333514)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 313893679.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.