GERMANTOWN, WI — 2010-12-22 00:00:00

OSHA Inspection: STOCK SIDING AND TRIM INC.

Planned inspection · Safety discipline

At a glance

On 2010-12-22 00:00:00, OSHA opened a planned safety inspection of STOCK SIDING AND TRIM INC. in W172 N10107 WOODBRIDGE LANE, GERMANTOWN, WI 53022 (NAICS 238170). OSHA activity number 315118679.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Stock Siding and Trim INC. — free Get an email when a new federal OSHA severe-injury report for Stock Siding and Trim INC. is published. One employer, no account, unsubscribe in one click.

Where did this inspection happen?

Establishment: STOCK SIDING AND TRIM INC.
Site address: W172 N10107 WOODBRIDGE LANE
City: GERMANTOWN
State: WI
ZIP: 53022
Mailing: 35929 LIBSON RD, OCONOMOWOC, WI 53066

What kind of inspection was it?

Inspection type: Planned (H)
Scope: Partial (B)
Discipline: Safety
Advance notice: No
Union status: N

When did the case open and close?

Opened: 2010-12-22 00:00:00
Closing conference: 2011-01-28 00:00:00
Case closed: 2012-02-17 00:00:00
Last modified: 2012-02-17 00:00:00
Data loaded: 2012-02-21 01:00:28

Establishment context

NAICS code: 238170
SIC code (legacy): 1761
Employees: 3
Ownership type: A

Citations

8 citations on file for this inspection.

5(a)(1)

Deleted Serious Gravity 10 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Mar 1, 2011
Penalty: Initial $4,200 · Current $4,200

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employment and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that employees were
exposed to a fall hazard while using a platform supported by a rough
terrain forklift.
(a)The employer failed to ensure that employees were protected from a fall
hazard
when utilizing a platform on a rough terrain forklift which was in excess
of the
safe width.  The wheel width of the rough terrain forklift (CAT TH63) was
approximately 8 feet, and the platform was approximately 12 feet wide,
exposing
employees to a fall hazard.
Among other methods, feasible and acceptable means to correct this hazard
is to:
(a)Ensure that the platform and rough terrain forklift are compatible for
wheel width
to platform width in accordance with American National Safety Standards for
Rough Terrain Forklift Trucks, ASME B56.6-2005 Section 8.24.1(b).  This
section states: floor dimensions shall not exceed two times the load center
distance listed on the rough terrain forklift truck nameplate, measured
parallel to
the longitudinal center plane of the truck, nor have a width greater than
the
overall width of the truck [measured across the load bearing tires plus 10
inches
(250mm) on either side].
(b)Ensure that any platform meets the conditions required by the
Caterpillar
Operations and Maintenance Manual, Safety Section, Machine with Access
Platform (page 24).
Certification, and documentation/evidence of abatement is required.
Certification of abatement is required by 29 CFR Part 1903 and is to be
submitted within ten (10)
calendar days after the abatement date.ment

Recent events (2)

2011-03-11 00:00:00 — I (S) $4200.00
2011-02-23 00:00:00 — Z (S) $4200.00

1926.451 A06

Deleted Serious Gravity 05 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Mar 28, 2011
Penalty: Initial $2,550 · Current $2,550

Recent events (2)

2011-03-11 00:00:00 — I (S) $2550.00
2011-02-23 00:00:00 — Z (S) $2550.00

1926.451 C02 V

Deleted Serious Gravity 05 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Mar 1, 2011
Penalty: Initial $2,550 · Current $2,550

Recent events (2)

2011-03-11 00:00:00 — I (S) $2550.00
2011-02-23 00:00:00 — Z (S) $2550.00

1926.451 G01

Deleted Serious Gravity 10 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Feb 28, 2011
Penalty: Initial $4,200 · Current $4,200

Recent events (2)

2011-03-11 00:00:00 — I (S) $4200.00
2011-02-23 00:00:00 — Z (S) $4200.00

5(a)(1)

Serious Gravity 10 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Mar 1, 2011
Penalty: Initial $4,200 · Current $2,100 Reduced

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employment and a place of employment which were free from recognized
hazards
that were
causing or likely to cause death or serious physical harm to employees in
that employees were
exposed to a fall hazard while using a platform supported by a rough
terrain forklift.
(a)The employer failed to ensure that employees were protected from a fall
hazard
when utilizing a platform on a rough terrain forklift which was in excess
of the
safe width.  The wheel width of the rough terrain forklift (CAT TH63) was
approximately 8 feet, and the platform was approximately 12 feet wide,
exposing
employees to a fall hazard.
Among other methods, feasible and acceptable means to correct this hazard
is to:
(a)Ensure that the platform and rough terrain forklift are compatible for
wheel width
to platform width in accordance with American National Safety Standards for
Rough Terrain Forklift Trucks, ASME B56.6-2005 Section 8.24.1(b).  This
section states: floor dimensions shall not exceed two times the load center
distance listed on the rough terrain forklift truck nameplate, measured
parallel to
the longitudinal center plane of the truck, nor have a width greater than
the
overall width of the truck [measured across the load bearing tires plus 10
inches
(250mm) on either side].
(b)Ensure that any platform meets the conditions required by the
Caterpillar
Operations and Maintenance Manual, Safety Section, Machine with Access
Platform (page 24).
Certification, and documentation/evidence of abatement is required.
Certification of abatement is required by 29 CFR Part 1903 and is to be
submitted within ten (10)
calendar days after the abatement date.ment

Recent events (2)

2011-03-11 00:00:00 — I (S) $2100.00
2011-02-23 00:00:00 — Z (S) $4200.00

1926.451 A06

Serious Gravity 05 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Mar 28, 2011
Penalty: Initial $2,550

Recent events (2)

2011-03-11 00:00:00 — I (S)
2011-02-23 00:00:00 — Z (S) $2550.00

1926.451 C02 V

Serious Gravity 05 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Mar 1, 2011
Penalty: Initial $2,550

Recent events (2)

2011-03-11 00:00:00 — I (S)
2011-02-23 00:00:00 — Z (S) $2550.00

1926.451 G01

Serious Gravity 10 1 instance 2 exposed

Issued: Feb 23, 2011
Abate by: Feb 28, 2011
Penalty: Initial $4,200

Recent events (2)

2011-03-11 00:00:00 — I (S)
2011-02-23 00:00:00 — Z (S) $4200.00

More inspections in this industry (NAICS 238170)

Jul 16, 2026 Bianco & Sons, LLC · EAST HAVEN, CT Jul 15, 2026 SJM General Contractors LLC · FORT LEE, NJ Jul 14, 2026 Torchylo Builders, LLC. · CLINTON, MO Jul 14, 2026 161545 - RHP Siding LLC · HIGH POINT, NC Jul 14, 2026 161544 - Triad Siding of Thomasville Incorporated · HIGH POINT, NC

More inspections in WI

Jul 17, 2026 PTS Contractors, INC. · GREEN BAY, WI Jul 16, 2026 Miron Construction CO. INC. · WAUSAU, WI Jul 15, 2026 Wabash National Services, L.P. · ELROY, WI Jul 15, 2026 Kings Superior Construction LLC · SUSSEX, WI Jul 15, 2026 Teronomy Builders, INC. · DELAVAN, WI

Source

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 315118679.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.