HARTLAND, WI — 2011-02-17 00:00:00

OSHA Inspection: WEBER CARPENTRY, LLC

Special Programs inspection · Safety discipline

At a glance

On 2011-02-17 00:00:00, OSHA opened a special Programs safety inspection of WEBER CARPENTRY, LLC in 1278 MARY HILL CIRCLE, HARTLAND, WI 53029 (NAICS 238130). OSHA activity number 315119610.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Weber Carpentry, LLC — free Get an email when a new federal OSHA severe-injury report for Weber Carpentry, LLC is published. One employer, no account, unsubscribe in one click.

Where did this inspection happen?

Establishment: WEBER CARPENTRY, LLC
Site address: 1278 MARY HILL CIRCLE
City: HARTLAND
State: WI
ZIP: 53029
Mailing: W208 MERIDAN ROAD, THERESA, WI 53091

What kind of inspection was it?

Inspection type: Special Programs (K)
Scope: Partial (B)
Discipline: Safety
Advance notice: No
Union status: N

When did the case open and close?

Opened: 2011-02-17 00:00:00
Closing conference: 2011-02-17 00:00:00
Case closed: 2013-04-15 00:00:00
Last modified: 2016-06-10 00:00:00
Data loaded: 2016-06-30 01:10:52

Establishment context

NAICS code: 238130
SIC code (legacy): 1751
Employees: 4
Ownership type: A

Citations

8 citations on file for this inspection.

5(a)(1)

Deleted Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200 · Current $4,200

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employment and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that an employee was
exposed to a fall, struck-by, and crushing hazards while using a platform
supported by a rough
terrain forklift.
(a)The wooden pallet being used as a work platform was approximate 12 feet
in
length and exceeded the allowable width capacity of the rough terrain
forklift in
that the width of the platform exceeded the maximum ten inches allowed
beyond
the load bearing tires. This exposed the employee to a tipping/fall hazard
of
approximately 22 feet.
Among other methods, feasible and acceptable means to correct this hazard
is to:
(a)Ensure that the platform and rough terrain forklift are compatible for
wheel width
to platform width in accordance with American National Standards Institute
ANSI/ITSDF B56.6-2005, Safety Standard for Rough Terrain Forklift Trucks,
Section 8.24.1(b). This section states: floor dimensions shall not exceed
two times
the load center distance listed on the rough terrain forklift truck
nameplate,
measured parallel to the longitudinal center plane of the truck nor have a
width
greater than the overall width of the truck [measured across the load
bearing tires
plus 10 inches (250mm) on either side].
(b)Ensure that any platform used is a JLG approved work platform as stated
in the
Skytrak Operations and Safety Manual on page 1-8.
Certification, and documentation/evidence of abatement is required.
Certification of abatement is required by 29 CFR Part 1903 and is to be
submitted within ten (10)
calendar days after the abatement date.ment

Recent events (2)

2011-07-05 00:00:00 — I (S) $4200.00
2011-06-22 00:00:00 — Z (S) $4200.00

1926.451 A06

Deleted Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200 · Current $4,200

Recent events (2)

2011-07-05 00:00:00 — I (S) $4200.00
2011-06-22 00:00:00 — Z (S) $4200.00

1926.451 C02 V

Deleted Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200 · Current $4,200

Recent events (2)

2011-07-05 00:00:00 — I (S) $4200.00
2011-06-22 00:00:00 — Z (S) $4200.00

1926.451 G01

Deleted Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200 · Current $4,200

Recent events (2)

2011-07-05 00:00:00 — I (S) $4200.00
2011-06-22 00:00:00 — Z (S) $4200.00

5(a)(1)

Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200 · Current $4,200

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer
did not furnish
employment and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that an employee was
exposed to a fall, struck-by, and crushing hazards while using a platform
supported by a rough
terrain forklift.
(a)The wooden pallet being used as a work platform was approximate 12 feet
in
length and exceeded the allowable width capacity of the rough terrain
forklift in
that the width of the platform exceeded the maximum ten inches allowed
beyond
the load bearing tires. This exposed the employee to a tipping/fall hazard
of
approximately 22 feet.
Among other methods, feasible and acceptable means to correct this hazard
is to:
(a)Ensure that the platform and rough terrain forklift are compatible for
wheel
width
to platform width in accordance with American National Standards Institute
ANSI/ITSDF B56.6-2005, Safety Standard for Rough Terrain Forklift Trucks,
Section 8.24.1(b). This section states: floor dimensions shall not exceed
two times
the load center distance listed on the rough terrain forklift truck
nameplate,
measured parallel to the longitudinal center plane of the truck nor have a
width
greater than the overall width of the truck [measured across the load
bearing tires
plus 10 inches (250mm) on either side].
(b)Ensure that any platform used is a JLG approved work platform as stated
in the
Skytrak Operations and Safety Manual on page 1-8.
Certification, and documentation/evidence of abatement is required.
Certification of abatement is required by 29 CFR Part 1903 and is to be
submitted within ten (10)
calendar days after the abatement date.ment

Recent events (2)

2011-07-05 00:00:00 — I (S) $4200.00
2011-06-22 00:00:00 — Z (S) $4200.00

1926.451 A06

Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200

Recent events (2)

2011-07-05 00:00:00 — I (S)
2011-06-22 00:00:00 — Z (S) $4200.00

1926.451 C02 V

Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200

Recent events (2)

2011-07-05 00:00:00 — I (S)
2011-06-22 00:00:00 — Z (S) $4200.00

1926.451 G01

Serious Gravity 10 1 instance 1 exposed

Issued: Jun 22, 2011
Abate by: Jun 27, 2011
Penalty: Initial $4,200

Recent events (2)

2011-07-05 00:00:00 — I (S)
2011-06-22 00:00:00 — Z (S) $4200.00

More inspections in this industry (NAICS 238130)

Jul 17, 2026 M and F Construction LLC · MOUNT JULIET, TN Jul 17, 2026 Carrillo Construction LLC · MERIDIAN, ID Jul 17, 2026 Sevy Brothers Construction LLC · MERIDIAN, ID Jul 17, 2026 M&M Construction Services Corp · WESTFORD, MA Jul 16, 2026 Francisco Arias · FAIRHOPE, AL

More inspections in WI

Jul 17, 2026 PTS Contractors, INC. · GREEN BAY, WI Jul 16, 2026 Miron Construction CO. INC. · WAUSAU, WI Jul 15, 2026 Wabash National Services, L.P. · ELROY, WI Jul 15, 2026 Kings Superior Construction LLC · SUSSEX, WI Jul 15, 2026 Teronomy Builders, INC. · DELAVAN, WI

Source

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 315119610.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.