15. ANN, MO ·
OSHA Inspection: AUTO TIRE INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of AUTO TIRE INC. in 3840 ADIE RD., 15. ANN, MO 63074 (NAICS 811111). OSHA activity number 315653295.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- AUTO TIRE INC.
- Site address
- 3840 ADIE RD.
- City
- 15. ANN
- State
- MO
- ZIP
- 63074
- Mailing
- 3840 ADIE RD., ST. ANN, MO 63074
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 811111
- SIC code (legacy)
- 7538
- Employees
- 7
- Ownership type
- Private (A)
- Industry flags
- Construction safety. Manufacturing safety. Maritime safety.
Citations
3 citations on file for this inspection.
5(a)(1)
- Issued
- Sep 2, 2011
- Abate by
- Sep 20, 2011
- Penalty
- Initial $4,410 · Current $3,087 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees operated automotive lifts of which periodic inspection was conducted. On or about 06/30/2011, the employer did not establish procedures to periodically inspect the automotive lifts used in the repair shop. Two Mohawk, 16,000 lbs. capacity, and three Rotary, 10,000 lbs. capacity automotive lifts were used on regular basis. Rotary lift, Model, SL 19N 300, located on the south east bay fails to keep the load in place by creeping 3-4 inches lower than the stop position, therefore, exposing the mechanics to serious injuries or death. One method of abatement to correct this apparent hazard is to periodically inspect the lifts as required by the Manufacturer, Rotary Operation & Maintenance Manual, SPOA10NB, SPOA10, SPO10, OWNER/EMPLOYER RESPONSIBILITY section, page 3, bullet, 2 that states the Owner/employer shall establish procedures to periodically inspect the lift in accordance with the lift manufacturer's instructions or ANSI/ALI ALOIM-2008. Abatement certification and abatement documentation is required for this violation. The documentation should include written verification of abatement, applicable measurements or monitoring results, and photographs or videos which you believe will be helpful. The abatement certification sheet is enclosed with the citations.
Recent events (2)
- · I (S) $3087.00
- · Z (S) $4410.00
1910.36 D01
- Issued
- Sep 2, 2011
- Abate by
- Sep 7, 2011
- Penalty
- Initial $4,410 · Current $3,087 Reduced
Recent events (2)
- · I (S) $3087.00
- · Z (S) $4410.00
1910.141 A05
- Issued
- Sep 2, 2011
- Abate by
- Sep 7, 2011
- Penalty
- Initial $1,890 · Current $1,323 Reduced
Recent events (2)
- · I (S) $1323.00
- · Z (S) $1890.00
More inspections in this industry (NAICS 811111)
More inspections in MO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 315653295.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.