MONROE, NC —
OSHA Inspection: G & G METAL ERECTORS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of G & G METAL ERECTORS, INC. in 2201 WALKUP AVENUE, MONROE, NC 28111 (NAICS 238120). OSHA activity number 315976787.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- G & G METAL ERECTORS, INC.
- Site address
- 2201 WALKUP AVENUE
- City
- MONROE
- State
- NC
- ZIP
- 28111
- Mailing
- 332 CEDAR BROOK DRIVE, KANNAPOLIS, NC 28081
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238120
- SIC code (legacy)
- 1791
- Employees
- 4
- Ownership type
- A
- Industry flags
- Construction safety.
Citations
7 citations on file for this inspection.
1903.19 C01
- Issued
- Feb 23, 2012
- Abate by
- Feb 28, 2012
- Penalty
- Initial $400 · Current $400
95012901
- Issued
- Dec 20, 2011
- Abate by
- Dec 28, 2011
- Penalty
- Initial $2,100 · Current $2,100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to fall and struck-by hazards: a)jobsite, on September 9, 2011, an employee worked from a work platform elevated by Sky Trak Lull Model Number 8042. The platform was too wide to be safely used by the 8-foot wide Lull, exposing the employee to fall and/or struck-by hazards. Among other methods, one feasible and acceptable means to correct these hazards are: Ensure employer consults with the Manufacturer, Lull operator's safety manual and specific load chart designated for the specific piece of equipment and attachments to determine proper load capacities, and the ANSI B56.6, which states: To be approved the fork-mounted personnel work platforms must comply with the following design requirements before the platform is used: "The platform floor dimensions shall not exceed: a. Two times the load center distance as identified on the load chart for the attachment being used. b. The platform shall not be wider than the width of the telehandler (excluding outriggers) plus 10 inches (250 mm) on each side. c. Minimum space for each platform occupant shall not be less than 18 inches (450 mm) in either direction."
1926.20 B02
- Issued
- Dec 20, 2011
- Abate by
- Jan 13, 2012
- Penalty
- Initial $2,100 · Current $2,100
1926.453 B02 V
- Issued
- Dec 20, 2011
- Abate by
- Dec 28, 2011
- Penalty
- Initial $2,100 · Current $2,100
1926.760 A01
- Issued
- Dec 20, 2011
- Abate by
- Jan 13, 2012
- Penalty
- Initial $2,100 · Current $2,100
1926.761 B
- Issued
- Dec 20, 2011
- Abate by
- Jan 13, 2012
- Penalty
- Initial $2,100 · Current $2,100
1926.602 C01 I
- Issued
- Dec 20, 2011
- Abate by
- Jan 13, 2012
More inspections at G & G Metal Erectors, INC.
View G & G Metal Erectors, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 238120)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 315976787.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.