CINCINNATI, OH —
OSHA Inspection: FEINTOOL CINCINNATI, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of FEINTOOL CINCINNATI, INC. in 11280 CORNELL PARK DR, CINCINNATI, OH 45242 (NAICS 336370). OSHA activity number 330970351.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- FEINTOOL CINCINNATI, INC.
- Site address
- 11280 CORNELL PARK DR
- City
- CINCINNATI
- State
- OH
- ZIP
- 45242
- Mailing
- 11280 CORNELL PARK DR, CINCINNATI, OH 45242
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336370
- Employees
- 250
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.305 G02 III
- Issued
- Aug 16, 2011
- Penalty
- Initial $2,295 · Current $1,100 Reduced
General-duty citation text
29 CFR 1910.305(g)(2)(iii): Flexible cords were not connected to devices and fittings so that tension would not be transmitted to joints or terminal screws: a) Flexible cord attached to the battery charger for the lift truck was not equipted with strain relief device to prevent movement. b) Flexible cord attached to press #400-4 at the vibration table was not equipted with strain relief device to prevent movement.
Recent events (2)
- — I (S) $1100
- — Z (S) $2295
1910.303 G02 I
- Issued
- Aug 16, 2011
- Penalty
- Initial $4,590 · Current $2,300 Reduced
General-duty citation text
29 CFR 1910.303(g)(2)(i): Except as elsewhere required or permitted by this standard, live parts of electric equipment operating at 50 volts or more shall be guarded against accidentalcontact by use of approved cabinets or other forms of approved enclosures or by any of the following means: a) Electrical battery charger for the lift truck was missing the rear cover exposing employees to live parts. b) The top outlets in a duplex receptacle in area 700-2 were broken, exposing employeees to contact with live parts. c) The electrical cord for the washing unit showed signs of the other covering cut in several areas exposing employees to contact th live parts.
Recent events (2)
- — I (S) $2300
- — Z (S) $4590
1910.219 C02 I
- Issued
- Aug 16, 2011
- Penalty
- Initial $3,060 · Current $0 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i):All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting:(a)(LOCATION)(IDENTIFY SPECIFIC OPERATION(S) AND/OR CONDITIONS)(DESCRIBE HAZARD(S) WHERE NECESSARY)(3)RUNWAYS USED EXCLUSIVELY FOR OILING OR RUNNING ADJUSTMENTS EXCLUDED. a) The shaft on the motor drive for the Tumbler on press #250-5 was not guarded.\r\nb) The shaft on the motor drive for the bench grinder in the new press area was not guarded.
Recent events (2)
- — I (O) $0
- — Z (S) $3060
1910.305 B01
- Issued
- Aug 16, 2011
- Penalty
- Initial $2,295 · Current $0 Reduced
General-duty citation text
29 CFR 1910.305(b)(1): Conductors entering boxes, cabinets, or fittings were not protected from abrasions:(a) (LOCATION) (IDENTIFY EQUIPMENT AND CONDITION(S)) (STATE HAZARD(S) TO EMPLOYEE(S)) a) Cord attached to the parts counter on press #250-9 was not protected form abrasion in that the cord enters a opening in the press.
Recent events (2)
- — I (O) $0
- — Z (S) $2295
1910.178 L01 I
- Issued
- Aug 16, 2011
- Abate by
- Aug 30, 2011
- Penalty
- Initial $3,060 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(i):The employer did not ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l): a) Operators of powered industrial lift trucks were not trained prior to being allowed to operate a forklift.
Recent events (2)
- — I (S) $1500
- — Z (S) $3060
1910.178 L04 II B
- Issued
- Aug 16, 2011
- Abate by
- Sep 6, 2011
- Penalty
- Initial $4,590 · Current $2,300 Reduced
General-duty citation text
29 CFR 1910.178(l)(4)(ii)(B): The operator has been involved in an accident or near-miss incident; a)On or about July 29, 2011 an accident occurred while operating a powered industrial lift truck and the operator was not retrained.
Recent events (2)
- — I (S) $2300
- — Z (S) $4590
1910.178 O01
- Issued
- Aug 16, 2011
- Abate by
- Aug 23, 2011
- Penalty
- Initial $4,590 · Current $2,300 Reduced
General-duty citation text
29 CFR 1910.178(o)(1):Only stable or safely arranged loads shall be handled. Caution shall be exercised when handling off-center loads which cannot be centered. a) On or about July 29, 2011 a load was not stable on a industrial lift truck in that material went of the fork unto an employee.
Recent events (2)
- — I (S) $2300
- — Z (S) $4590
More inspections at Feintool Cincinnati, INC.
View Feintool Cincinnati, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 336370)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 330970351.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.