Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: STEEL WAREHOUSE

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of STEEL WAREHOUSE in 4700 HEIDTMAN PARKWAY, CLEVELAND, OH 44105 (NAICS 484121). OSHA activity number 330971466.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Steel Warehouse — free Get an email when a new federal OSHA severe-injury report for Steel Warehouse is published. One employer, no account, unsubscribe in one click.
Establishment
STEEL WAREHOUSE
Site address
4700 HEIDTMAN PARKWAY
City
CLEVELAND
State
OH
ZIP
44105
Mailing
4700 HEIDTMAN PARKWAY, CLEVELAND, OH 44105
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
484121
Employees
50
Ownership type
A

6 citations on file for this inspection.

1910.23 A08

Deleted Serious Gravity 5 1 instance 1 exposed
Issued
Jan 18, 2012
Abate by
Jan 20, 2012
Penalty
Initial $4,200 · Current $0 Reduced
29 CFR 1910.23(a)(8):     Every floor hole into which persons can accidentally walk shall be guardeded:    A floor hole, approximately 4-6" deep and 15" X 17", located in the South Low Bay, near the shears, was not guarded.
Recent events (3)
  • — F (S) $4200
  • — C (S) $4200
  • — Z (S) $4200

1910.147 C04 I

Serious Gravity 10 1 instance 3 exposed
Issued
Jan 18, 2012
Abate by
Feb 17, 2012
Penalty
Initial $4,900 · Current $3,500 Reduced
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section:                                                                                                                                   Written energy control procedures were not affixed  the the Spartan Marvel Ironworker.
Recent events (3)
  • — F (S) $3500
  • — C (S) $4900
  • — Z (S) $4900

1910.147 D04 I

Deleted Serious Gravity 10 1 instance 1 exposed
Issued
Jan 18, 2012
Abate by
Feb 17, 2012
Penalty
Initial $0 · Current $0
DESCRIPTION  29 CFR 1910.147(d)(4)(i):  Lockout or tagout devices were not affixed to each energy isolating device by authorized employees:    On 7/18/11,  an employees (torch) cutting coils, on the Cut Line, did not affix locks and tags to energy isolating devices.
Recent events (3)
  • — F (S) $0
  • — C (S) $0
  • — Z (S) $0

1910.212 A01

Serious Gravity 10 4 instances 2 exposed
Issued
Jan 18, 2012
Abate by
Sep 26, 2012
Penalty
Initial $4,900 · Current $3,500 Reduced
29 CFR 1910.212(a)(1):  One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    Machine guarding was not provided for machines such as; but not limited to the following:    1.  DBI SWC34-BY013 Cut Line  (unguarded stacker; in-running side of shear);    2.  Spartan Marvel Ironworker (point of operation), located on the platform of the Cut Line;    3.  Spacing of the roller conveyors on the Cutline (in-running nip points);    4.  Area underneath coil-straightening portion (unguarded from lower edge to the floor).
Recent events (3)
  • — F (S) $3500
  • — C (S) $4900
  • — Z (S) $4900

1910.219 C04 I

Other-than-serious 1 instance 2 exposed
Issued
Jan 18, 2012
Abate by
Jan 28, 2012
Penalty
Initial $2,800 · Current $0 Reduced
29 CFR 1910.219(c)(4)(i):  Unguarded projecting shaft end(s) did not present a smooth edge and end and projected more than one half the diameter of the shaft:    Projecting shaft ends, located on the out feed side of the DBI SWC34-BY013 Cut Line, were not guarded.
Recent events (3)
  • — F (O) $0
  • — C (S) $2800
  • — Z (S) $2800

1904.40 A

Deleted Other-than-serious 1 instance 5 exposed
Issued
Jan 18, 2012
Abate by
Jan 21, 2012
Penalty
Initial $700 · Current $0 Reduced
29 CFR 1904.40(a): Copies of records kept under Part 1904 requested by an authorized government representative were not provided within four (4) business hours.    On 7/18/11, OSHA 300 logs were not available for review by authorized OSHA representatives.
Recent events (3)
  • — F (O) $700
  • — C (O) $700
  • — Z (O) $700

View Steel Warehouse's full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 330971466.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.