BLOOMER, WI —
OSHA Inspection: A.J. MANUFACTURING INCORPORATED
Complaint inspection · Health discipline
At a glance
On , OSHA opened a complaint health inspection of A.J. MANUFACTURING INCORPORATED in 105 RIGGS STREET, BLOOMER, WI 54724 (NAICS 332321). OSHA activity number 331099952.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- A.J. MANUFACTURING INCORPORATED
- Site address
- 105 RIGGS STREET
- City
- BLOOMER
- State
- WI
- ZIP
- 54724
- Mailing
- 1217 OAK STREET, BLOOMER, WI 54724
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332321
- Employees
- 62
- Ownership type
- A
Citations
8 citations on file for this inspection.
1910.147 C04 I
- Issued
- Feb 28, 2012
- Abate by
- Mar 13, 2012
- Penalty
- Initial $2,700 · Current $1,890 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: (a) Main production floor; Machine specific energy control procedures were not developed for machines with multiple energy sources, such as, but not limited to; Foam gun, foam press.
Recent events (2)
- — I (S) $1890
- — Z (S) $2700
1910.147 C06 I
- Issued
- Feb 28, 2012
- Abate by
- Mar 13, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed: (a) Throughout the facility; Energy control procedures were not evaluated at least annually.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 D04 I
- Issued
- Feb 28, 2012
- Abate by
- Mar 13, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: (a) Main production floor; Employees did not isolate the stored energies of the pressurized foam and pneumatic sources while conducting servicing and/ or maintenance tasks, such as, but not limited to, cleaning of the foam gun.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A03 II
- Issued
- Feb 28, 2012
- Abate by
- Mar 20, 2012
- Penalty
- Initial $4,500 · Current $3,150 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): (a) Main production floor; The point of operation of the JCI Frame Punch #57 was not guarded. (b) Main production floor; The point of operation of the JCI Corner Frame Punch #57 was not guarded. (c) Main production floor; The point of operation of the Jet H/V band saw had 5" of unguarded blade. (d) Main production floor; The point of operation of the Installation Punch #34 was not guarded.
Recent events (2)
- — I (S) $3150
- — Z (S) $4500
1910.215 B09
- Issued
- Feb 28, 2012
- Abate by
- Mar 2, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch: (a) Maintenance shop; The right upper tongue of an Erco 8" bench grinder was adjusted beyond 1/4".
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E01 I
- Issued
- Feb 28, 2012
- Abate by
- Mar 20, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs seven -7 feet or less from the floor level were not guarded with a guard that extended to at least fifteen inches above the belt: (a) Maintenance shop; The Bridgeport mill drive belts below 7 feet were partially exposed on two sides.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.134 C02 I
- Issued
- Feb 28, 2012
- Abate by
- Mar 20, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.134(c)(2)(i): Respirator users were not provided with the information contained in Appendix D to 29 CFR 1910.134 when the employer determined that any voluntary respirator use was permissible: (a) Employees voluntarily used respirators and were not provided with 1910.134 Appendix D information.
Recent events (2)
- — I (O) $0
- — Z (O) $0
1910.252 C02 II
- Issued
- Feb 28, 2012
- Abate by
- Mar 28, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.252(c)(2)(ii): Mechanical ventilation provided did not meet the minimum rate of 2,000 cubic feet (57 m3) per minute per welder: (a) Main shop floor; Air velocity at the welding booth next to the robot welder was measured at 0 foot per minute at the operators station with the welding fume ventilation system running.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections in this industry (NAICS 332321)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 331099952.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.