LOWELLVILLE, OH ·
OSHA Inspection: RAVANA INDUSTRIES INC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of RAVANA INDUSTRIES INC in 6150 CENTER RD, LOWELLVILLE, OH 44436 (NAICS 332710). OSHA activity number 332803550.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- RAVANA INDUSTRIES INC
- Site address
- 6150 CENTER RD
- City
- LOWELLVILLE
- State
- OH
- ZIP
- 44436
- Mailing
- 6150 CENTER RD, LOWELLVILLE, OH 44436
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 7
- Ownership type
- Private (A)
Citations
10 citations on file for this inspection.
1910.132 D01
- Issued
- May 31, 2012
- Abate by
- Jun 15, 2012
- Penalty
- Initial $2,400 · Current $0 Reduced
General-duty citation text
29 CFR 1910.132(d)(1): The employer did not assess the workplace to determine if hazards are present, or are likely to be present, which necessitate the use of personal protective equipment (PPE): On and before 3/12/2012, the employer did not conduct a personal protective equipment hazard assessment for occupations such as but not limited to welders.
Recent events (3)
- · F (O) $0
- · C (S) $2400
- · Z (S) $2400
1910.147 C01
- Issued
- May 31, 2012
- Abate by
- Jun 30, 2012
- Penalty
- Initial $3,000 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: On and before 3/12/2012, the employer did not have a lockout tagout program for machinery such as but not limited to the Edwards ironworker, Marvel vertical bandsaw and the Cleveland hydraulic press.
Recent events (3)
- · F (S) $0
- · C (S) $3000
- · Z (S) $3000
1910.157 G01
- Issued
- May 31, 2012
- Abate by
- Jun 30, 2012
- Penalty
- Initial $1,800 · Current $0 Reduced
General-duty citation text
29 CFR 1910.157(g)(1): An educational program was not provided for all employees to familiarize them with the general principles of fire extinguisher use and the hazards involved with incipient stage fire fighting: On and before 3/12/2012, the employer did not provide portable fire extinguisher training.
Recent events (3)
- · F (O) $0
- · C (S) $1800
- · Z (S) $1800
1910.178 L01 I
- Issued
- May 31, 2012
- Abate by
- Jun 30, 2012
- Penalty
- Initial $3,000 · Current $0 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(i): The employer did not ensure that each powered industrial truck operator was competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l): On and before 3/12/2012, the employer had 6 forklift operators who did not recieve training and evaluation.
Recent events (3)
- · F (O) $0
- · C (S) $3000
- · Z (S) $3000
1910.178 Q07
- Issued
- May 31, 2012
- Abate by
- Jun 15, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.178(q)(7): Industrial trucks were not examined before being placed in service: On and before 3/12/2012, the 5 propane and 1 electric forklifts did not receive an inspection before being placed in service.
Recent events (3)
- · F (O) $0
- · C (S) $0
- · Z (S) $0
1910.179 J02
- Issued
- May 31, 2012
- Abate by
- Jun 15, 2012
- Penalty
- Initial $3,000 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.179(j)(2): The following items were not be inspected for defects at intervals as defined in paragraph (j)(1)(ii) of this section or as specifically indicated, including observation during operation for any defects which might appear between regular inspections: On and before 3/12/2012, the two overhead cranes in the fab shop did not recieve a frequent (daily/monthly) inspection, including there were bumper stops missing from the 25 ton crane.
Recent events (3)
- · F (S) $1500
- · C (S) $3000
- · Z (S) $3000
1910.179 J03
- Issued
- May 31, 2012
- Abate by
- Jun 30, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.179(j)(3): A complete periodic inspection of crane(s) had not been conducted in the past 12 months: On and before 3/12/2012, the two overhead cranes in the fab shop did not receive the required periodic inspection.
Recent events (3)
- · F (S) $0
- · C (S) $0
- · Z (S) $0
1910.212 A01
- Issued
- May 31, 2012
- Abate by
- Jun 5, 2012
- Penalty
- Initial $2,400 · Current $1,200 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: On 3/12/2012, the Marvel vertical bandsaw had 12 inches of the unused portion of the sawblade that was not guarded including underneath the platen was open, exposing the bottom section of the sawblade and drive wheel.
Recent events (3)
- · F (S) $1200
- · C (S) $2400
- · Z (S) $2400
1910.212 A03 II
- Issued
- May 31, 2012
- Abate by
- Jun 15, 2012
- Penalty
- Initial $3,000 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): On 3/12/2012, the Edwards ironworker punch press and the Cleveland hydraulic press were not guarded at the point of operation.
Recent events (3)
- · F (S) $1500
- · C (S) $3000
- · Z (S) $3000
1910.219 I02
- Issued
- May 31, 2012
- Abate by
- Jun 5, 2012
- Penalty
- Initial $2,400 · Current $1,200 Reduced
General-duty citation text
29 CFR 1910.219(i)(2): Revolving surfaces of shaft coupling(s) were not covered by a safety sleeve: On 3/12/2012, the Cleveland press hydraulic system had a motor to pump coupling that was not guarded.
Recent events (3)
- · F (S) $1200
- · C (S) $2400
- · Z (S) $2400
More inspections at Ravana Industries INC
View Ravana Industries INC's full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 332803550.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.