SPRING HILL, KS ·
OSHA Inspection: ADVANTAGE COMPONENT SYSTEMS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of ADVANTAGE COMPONENT SYSTEMS, INC. in 701 N. LINCOLN, SPRING HILL, KS 66083 (NAICS 321912). OSHA activity number 333915098.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ADVANTAGE COMPONENT SYSTEMS, INC.
- Site address
- 701 N. LINCOLN
- City
- SPRING HILL
- State
- KS
- ZIP
- 66083
- Mailing
- 701 N. LINCOLN, SPRING HILL, KS 66083
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321912
- Employees
- 40
- Ownership type
- Private (A)
Citations
3 citations on file for this inspection.
1910.212 A01
- Issued
- May 18, 2012
- Abate by
- Jun 4, 2012
- Penalty
- Initial $1,785 · Current $1,250 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): Machine guarding was not provided to protect operator(s) and other employees from hazard(s) created by rotating parts: Employee(s) operating a Delta drill press at the northwest corner of the maintenance room were exposed to physical injuries due to no guard being provided to prevent inadvertent contact with a rotating drill press chuck and drill bit. The Delta drill press can operate between 500 - 3,100 revolutions per minute.
Recent events (2)
- · I (S) $1249.5
- · Z (S) $1785
1910.219 D01
- Issued
- May 18, 2012
- Abate by
- Jun 11, 2012
- Penalty
- Initial $1,785 · Current $1,250 Reduced
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): (a) Employee(s) operating a belt sander at the southwest corner of the maintenance room were exposed to physical injuries due to no guard being provided for the 2 inch and 3 inch diameter pulleys on the left side of the machine. The belt sander operates at approximately 1,760 revolutions per minute. (b) Employee(s) operating a belt sander at the southwest corner of the maintenance room were exposed to physical injuries due to no guard being provided for the sanding belt pulleys on the right side of the machine. The belt sander operates at approximately 1,760 revolutions per minute.
Recent events (2)
- · I (S) $1249.5
- · Z (S) $1785
1910.219 E01 I
- Issued
- May 18, 2012
- Abate by
- Jun 11, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs seven feet or less from the floor level were not guarded with a guard that extended to at least fifteen inches above the belt: Employee(s) operating a belt sander at the southwest corner of the maintenance room were exposed to physical injuries due to no guard being provided for an approximately 14 inch horizontal belt rotating at approximately 1,760 rpms on the left side of the machine.
Recent events (2)
- · I (S) $0
- · Z (S) $0
More inspections at Advantage Component Systems, INC.
View Advantage Component Systems, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 321912)
More inspections in KS
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 333915098.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.