BELLAIRE, TX —
OSHA Inspection: MCT SHEET METAL, INC.
Unprogrammed Other inspection · Safety discipline
At a glance
On , OSHA opened an unprogrammed Other safety inspection of MCT SHEET METAL, INC. in 4548 BISSONNET ST., BELLAIRE, TX 77401 (NAICS 238390). OSHA activity number 334349511.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MCT SHEET METAL, INC.
- Site address
- 4548 BISSONNET ST.
- City
- BELLAIRE
- State
- TX
- ZIP
- 77401
- Mailing
- 29210 QUAIL, KATY, TX 77493
What kind of inspection was it?
- Inspection type
- Unprogrammed Other (I)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238390
- Employees
- 30
- Ownership type
- A
Citations
3 citations on file for this inspection.
1926.451 B01 I
- Issued
- Aug 22, 2012
- Abate by
- Sep 6, 2012
- Penalty
- Initial $4,200 · Current $2,100 Reduced
General-duty citation text
29 CFR 1926.451(b)(1)(i): Each platform unit (e.g., scaffold plank, fabricated plank, fabricated deck, or fabricated platform) shall be installed so that the space between adjacent units and the space between the platform and the uprights is no more than 1 inch (2.5 cm) wide, except where the employer can demonstrate that a wider space is necessary (for example, to fit around uprights when side brackets are used to extend the width of the platform). On the second floor patio, May 15, 2012, Employees were working from a bakers scaffold that was not fully planked, exposing employees to falls.
Recent events (2)
- — I (S) $2100
- — Z (S) $4200
1926.451 E01
- Issued
- Aug 22, 2012
- Abate by
- Sep 6, 2012
- Penalty
- Initial $4,200 · Current $2,100 Reduced
General-duty citation text
29 CFR 1926.451(e)(1): When scaffold platforms were more than 2 feet (0.6 m) above or below a point of access, portable ladders, hook-on ladders, attachable ladders, stair towers (scaffold stairways/towers), stairway-type ladders (such as ladder stands), ramps, walkways, integral prefabricated scaffold access, or direct access from other scaffold, sturcure, personnel hoist, or similar surface was not used. Crossbraces were used as a means of access. On the second floor patio, May 15, 2012, Employees were accessing bakers scaffolding where the first step of the ladder was greater than 24 inches, exposing employees to falls.
Recent events (2)
- — I (S) $2100
- — Z (S) $4200
1926.451 G01
- Issued
- Aug 22, 2012
- Abate by
- Sep 6, 2012
- Penalty
- Initial $4,900 · Current $2,454 Reduced
General-duty citation text
29 CFR 1926.451(g)(1): Employees on scaffolds more than 10 feet (3.1 m) above a lower level were not protected from falling to that lower level by fall protection established in paragraphs (g)(1)(i)-(vii) of this section: On the second floor patio, May 15, 2012, Employees were working from a bakers scaffold that did not have a mid-rail or a top rail exposing employees to falls great than 10 feet.
Recent events (2)
- — I (S) $2454
- — Z (S) $4900
More inspections at MCT Sheet Metal, INC.
View MCT Sheet Metal, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 238390)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 334349511.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.