GERALD, MO —
OSHA Inspection: GERALD INDUSTRIES INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of GERALD INDUSTRIES INC. in 625 W. INDUSTRIAL PARK, GERALD, MO 63037 (NAICS 332919). OSHA activity number 334473154.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Gerald Industries INC. — free
Get an email when a new federal OSHA severe-injury report for Gerald Industries INC. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- GERALD INDUSTRIES INC.
- Site address
- 625 W. INDUSTRIAL PARK
- City
- GERALD
- State
- MO
- ZIP
- 63037
- Mailing
- P.O. BOX 26664, SAINT LOUIS, MO 63122
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332919
- Employees
- 60
- Ownership type
- A
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Jun 6, 2012
- Abate by
- Jul 19, 2012
- Penalty
- Initial $4,500 · Current $2,250 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazards of amputation: Two-hand operating levers belonging to the following machines were not protected against premature or accidental cycling: Inside of the 3 through 5 line: a/ NEFF Pneumatic/Hydraulic Press, s/n P9177. b/ Air-Hydraulic Press, m/n C-250, s/n 2550. c/ Air-Hydraulic Press, m/n C-250, s/n 1191/J3755. Inside of the valve cell department: a/ Denison Multi-Press, m/n 6135. b/ Denison Multi-Press, m/n T-7018. One method of abatement to correct this apparent hazard is to construct each two-hand operating lever so that it cannot be prematurely or accidentally cycled as required by ANSI B11.19-1990, paragraph 4.2.4.2.1. DISCLAIMER: a/ The employer is not limited to the abatement method(s) suggested by OSHA. b/ The employer is responsible for selecting and implementing an effective abatement method.
Recent events (2)
- — I (S) $2250
- — Z (S) $4500
1910.212 A01
- Issued
- Jun 6, 2012
- Abate by
- Jul 19, 2012
- Penalty
- Initial $6,300 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: Chucks and/or the unused portion of the bit belonging to the following machines were unguarded: Inside of the 3 through 5 line: a/ ACRA Drill Press, m/n RL88DP12583N. b/ Wilton 6S Drill Press, m/n A3836, s/n 8041589. c/ Jet 15-Inch Drill Press, s/n 10121280. d/ Jet 15-Inch Bench Drill Press, s/n 11011412. e/ Wilton 6S Drill Press, m/n A3836, s/n 8021501. f/ Craftsman Drill Press, m/n 5K696BA. g/ Delta Rockwell Drill Press, series number, 15-665, s/n 1488394. Inside of the valve cell department: a/ Electro-Mechanical Drill Press, m/n 601J, s/n 96010. b/ Jet Drill Press, m/n JDP-14M, s/n 8051165. c/ Wilton Drill Press, m/n 2530, s/n 96100091. d/ Wilton Drill Press, m/n 2530, s/n 96100085. e/ Wilton Drill Press, m/n 2530, s/n 96100095. f/ Wilton Drill Press, m/n 2530, s/n 96100086. g/ Wilton Drill Press, m/n 2530, s/n 96100094. h/ Continental Ultient Drill Press, m/n DP-14-100, s/n 0639. Inside of the catch-all department: a/ Bridgeport Milling Machine, CAFC-2201. b/ Unknown make drill press, CAFC-0501. c/ ENCO Drill Press, CAFC-0502. d/ Victor Lathe, CAFC-0402. e/ Warner & Swasey Lathe, CAFC-0404. f/ Hendley Lathe, CAFC-0523. Inside of the maintenance shop: a/ Turnmaster Lathe, MDMD-0405. b/ Jet Drill Press, MDMD-0503. c/ Bridgeport Milling Machine, MDMD-2022.
Recent events (2)
- — I (S) $0
- — Z (S) $6300
1910.212 B
- Issued
- Jun 6, 2012
- Abate by
- Jul 19, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.212(b): Machine(s) designed for fixed location(s) were not securely anchored to prevent walking or moving: The following machines were not bolted or otherwise secured: Inside of the 3 through 5 line: a/ ACRA Drill Press, m/n RL88DP12583N. b/ Wilton 6S Drill Press, m/n A3836, s/n 8041589. c/ Jet 15-Inch Drill Press, s/n 10121280. d/ Jet 15-Inch Bench Drill Press, s/n 11011412. e/ Wilton 6S Drill Press, m/n A3836, s/n 8021501. f/ Craftsman Drill Press, m/n 5K696BA. g/ Delta Rockwell Drill Press, series number, 15-665, s/n 1488394. h/ Westward Six-Inch Pedestal Grinder, unknown m/n or s/n. i/ Westward Six-Inch Pedestal Grinder, unknown m/n or s/n Inside of the valve cell department: a/ Electro-Mechanical Drill Press, m/n 601J, s/n 96010. b/ Jet Drill Press, m/n JDP-14M, s/n 8051165. c/ Wilton Drill Press, m/n 2530, s/n 96100091. d/ Wilton Drill Press, m/n 2530, s/n 96100085. e/ Wilton Drill Press, m/n 2530, s/n 96100095. f/ Wilton Drill Press, m/n 2530, s/n 96100086. g/ Wilton Drill Press, m/n 2530, s/n 96100094. h/ Continental Ultient Drill Press, m/n DP-14-100, s/n 0639. Inside of the catch-all department: a/ Bridgeport Milling Machine, CAFC-2201. b/ Unknown make drill press, CAFC-0501. c/ ENCO Drill Press, CAFC-0502. Inside of the maintenance shop: a/ Jet Drill Press, MDMD-0503. b/ Bridgeport Milling Machine, MDMD-2022.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.217 D06 I
- Issued
- Jun 6, 2012
- Abate by
- Jul 19, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(d)(6)(i): Tonnage and stroke requirements were neither stamped on die(s) nor recorded on records readily available to the die setter: a/ Inside of the catch-all department, the die belonging to a Federal 80T Punch Press, s/n 7803, was neither stamped nor recorded in any way.
Recent events (2)
- — I (O) $0
- — Z (O) $0
1910.217 D06 II
- Issued
- Jun 6, 2012
- Abate by
- Jul 19, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(d)(6)(ii): Die(s) were not stamped to indicate upper die weight when it was necessary for air counter balance pressure adjustment: a/ Inside of the catch-all department, the die belonging to a Federal 80T Punch Press, s/n 7803, was neither stamped nor recorded in any way to indicate its upper die weight.
Recent events (2)
- — I (O) $0
- — Z (O) $0
1910.217 D06 III
- Issued
- Jun 6, 2012
- Abate by
- Jul 19, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(d)(6)(iii): Dies were not stamped to indicate die weight where handling equipment could become overloaded: a/ Inside of the catch-all department, the die belonging to a Federal 80T Punch Press, s/n 7803, was neither stamped nor recorded in any way to indicate its die weight.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Gerald Industries INC.
View Gerald Industries INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332919)
May 27, 2026
ETI LLC · GENEVA, IN
May 19, 2026
Victaulic Company · DULUTH, GA
May 7, 2026
Campbell Manufacturing, LLC · BECHTELSVILLE, PA
Apr 23, 2026
WA317990909 - Hilton Acquisition Company LLC · REDMOND, WA
Apr 22, 2026
77439 - Parker Aerospace · MONCKS CORNER, SC
More inspections in MO
Jul 17, 2026
United Parcel Service · SAINT LOUIS, MO
Jul 15, 2026
Triple J Construction, LLC. · PLATTE CITY, MO
Jul 14, 2026
Torchylo Builders, LLC. · CLINTON, MO
Jul 13, 2026
Jorge Merida · BLUE SPRINGS, MO
Jul 9, 2026
Niagara Bottling · KANSAS CITY, MO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 334473154.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.