FENTON, MO —
OSHA Inspection: BUCKERT MOLD & MACHINE CO.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of BUCKERT MOLD & MACHINE CO. in 767 SUNPARK DRIVE, FENTON, MO 63026 (NAICS 326199). OSHA activity number 334771383.
Watch Buckert Mold & Machine CO. — free
Get an email when a new federal OSHA severe-injury report for Buckert Mold & Machine CO. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- BUCKERT MOLD & MACHINE CO.
- Site address
- 767 SUNPARK DRIVE
- City
- FENTON
- State
- MO
- ZIP
- 63026
- Mailing
- 767 SUNPARK DRIVE, FENTON, MO 63026
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 326199
- Employees
- 12
- Ownership type
- A
Citations
11 citations on file for this inspection.
1910.132 D02
- Issued
- Abate by
- Penalty
- Initial $2400.00 · Current $0.00 Reduced
General-duty citation text
29 CFR 1910.132(d)(2): The employer did not verify, through a written certification, that the required workplace hazard assessment had been performed: a/ The workplace hazard assessment was not certified.
Recent events (2)
- — I (S) $0
- — Z (S) $2400
1910.133 A02
- Issued
- Abate by
- Penalty
- Initial $0.00 · Current $0.00
General-duty citation text
29 CFR 1910.133(a)(2): The employer did not ensure that each affected employee using eye protection that provides side protection when there was a hazard from flying objects. Detachable side protectors (e.g. clip-on or slide-on side shields) meeting the pertinent requirements of this section are acceptable. a/ Inside of the tool room, employee(s) were wearing prescription eye glasses that were not equipped with side shields. The employee(s) were operating a Comet XT Milling Machine at the time exposure was observed.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C04 I
- Issued
- Abate by
- Penalty
- Initial $2000.00 · Current $1000.00 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: Inside of the production department, specific lockout/tagout procedures for the following machines were not documented: a/ Cincinnati Milacron 300 Molding Machine, 480/240 volts, 300T/150T hydraulics, and 370 degrees Fahrenheit. b/ Van Dorn 200T Molding Machine, m/n 200-RS-14F, 480 volts, 200T hydraulics, 370-500 degrees Fahrenheit. c/ Small Negri Bossi & Co. Molding Machine, s/n 0-5820-76, 480 volts, 45T hydraulics, 500 degrees Fahrenheit.
Recent events (2)
- — I (S) $1000
- — Z (S) $2000
1910.147 C07 IV
- Issued
- Abate by
- Penalty
- Initial $0.00 · Current $0.00
General-duty citation text
29 CFR 1910.147(c)(7)(iv): The employer did not certify that employee training had been accomplished and kept up to date: a/ Employee training in lockout/tagout had not been certified.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A01
- Issued
- Abate by
- Penalty
- Initial $2000.00 · Current $1000.00 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: Inside of the tool room, the chucks belonging to the following machines were not guarded: a/ Comet-XT Milling Machine, unknown m/n or s/n. b/ Bridgeport Milling Machine, s/n T5T 9Z-2. c/ Comet Milling Machine, s/n 863622. d/ ENCO Lathe, s/n 10254. e/ Sharp Lathe, m/n 1540. f/ Cincinnati Milling Machine, s/n PB-5423. g/ Carlton Radial Arm Milling Machine, m/n 524. h/ Johnson Horizontal Band Saw, s/n 8335. i/ Manhattan Supply Co. Drill Press, m/n 951215. j/ Sears Craftsman Drilling Machine 15" Drill Press, unknown m/n or s/n.
Recent events (2)
- — I (S) $1000
- — Z (S) $2000
1910.215 A02
- Issued
- Abate by
- Penalty
- Initial $2000.00 · Current $1000.00 Reduced
General-duty citation text
29 CFR 1910.215(a)(2): Abrasive wheel(s) used on grinding machinery were not provided with safety guard(s) which covered the spindle end, nut, flange projections: a/ Inside of the tool room, the Buffalo Bench Grinder, m/n B-692, was not provided with a safety guard that covered the spindle end, nut, and flange projections.
Recent events (2)
- — I (S) $1000
- — Z (S) $2000
1910.215 A04
- Issued
- Abate by
- Penalty
- Initial $0.00 · Current $0.00
General-duty citation text
29 CFR 1910.215(a)(4): Grinding machinery was not used with work rest(s) to support offhand grinding work: a/ Inside of the tool room, the Buffalo Bench Grinder, m/n B-692, was not equipped with a work rest.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.215 B09
- Issued
- Abate by
- Penalty
- Initial $0.00 · Current $0.00
General-duty citation text
29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch: a/ Inside of the tool room, the distance between the upper peripheral guard and the abrasive wheel belonging to the Buffalo Bench Grinder, m/n B-692, was approximately one-half inch.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 D01
- Issued
- Abate by
- Penalty
- Initial $2000.00 · Current $1000.00 Reduced
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a/ Inside of the tool room, two pulleys belonging to the Van Norman Piston Turning & Grinding Machine, s/n 1458, were not guarded.
Recent events (2)
- — I (S) $1000
- — Z (S) $2000
1910.219 E03 I
- Issued
- Abate by
- Penalty
- Initial $0.00 · Current $0.00
General-duty citation text
29 CFR 1910.219(e)(3)(i): Vertical or inclined belt(s) were not enclosed by guard(s) conforming to the requirements specified at 29 CFR 1910.219(m) and (o): a/ Inside of the tool room, two inclined belts belonging to the Van Norman Piston Turning & Grinding Machine, s/n 1458, were unguarded.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.1200 E01
- Issued
- Abate by
- Penalty
- Initial $0.00 · Current $0.00
General-duty citation text
29 CFR 1910.1200(e)(1): The employer did not develop, implement, and/or maintain at the workplace a written hazard communication program which describes how the criteria specified in 29 CFR 1910.1200(f), (g), and (h) will be met: a/ A written hazard communication program was not developed that addressed how container labeling (f), material safety data sheets (g), and employee training will be managed.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at BUCKERT MOLD & MACHINE CO.
FENTON, MO—2012-12-19 00:00:00
BUCKERT MOLD & MACHINE CO.
View BUCKERT MOLD & MACHINE CO.'s full OSHA safety record →
More inspections in this industry (NAICS 326199)
CONNEAUT, OH—2026-07-13
CONTINENTAL STRUCTURAL PLASTICS
PETALUMA, CA—2026-07-10
LABCON NORTH AMERICA
KEEWATIN, MN—2026-07-09
111565 - TACKLE TAMER PRODUCTS INC
EAST FLAT ROCK, NC—2026-07-09
161517 - ELKAMET, INC.
LANESBOROUGH, MA—2026-07-08
LANSEN MOLD CO., INC.
More inspections in MO
KANSAS CITY, MO—2026-07-09
NIAGARA BOTTLING
MONETT, MO—2026-07-09
MONETT METALS INC.
PARKVILLE, MO—2026-07-08
SKY-TECH ROOFING, LLC.
SPRINGFIELD, MO—2026-07-07
D & C CONSTRUCTION, LLC.
JOPLIN, MO—2026-07-07
SERVICE RECYCLING - NORTH PLANT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 334771383.