LAFAYETTE, LA ·
OSHA Inspection: PARK GROUP CONSTRUCTION, L.L.C.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of PARK GROUP CONSTRUCTION, L.L.C. in 518 S. PIERCE, LAFAYETTE, LA 70501 (NAICS 236116). OSHA activity number 335398186.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PARK GROUP CONSTRUCTION, L.L.C.
- Site address
- 518 S. PIERCE
- City
- LAFAYETTE
- State
- LA
- ZIP
- 70501
- Mailing
- 326 SETTLERS TRACE BLVD SUITE 100B, LAFAYETTE, LA 70508
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 236116
- Employees
- 10
- Ownership type
- Private (A)
Citations
3 citations on file for this inspection.
1926.405 G01 I
- Issued
- Nov 1, 2012
- Abate by
- Nov 11, 2012
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1926.405(g)(1)(i): Flexible cords and cables were not suitable for conditions of use and location: On or about July 17, 2012, the employer failed to ensure that flexible cords were suitable for use in wet locations. A flexible cord ran through water and was used as a power source for a DeWalt circular saw. Employees were using the circular saw to cut angle iron.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1926.405 G02 III
- Issued
- Nov 1, 2012
- Abate by
- Nov 11, 2012
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1926.405(g)(2)(iii): Splices. Flexible cords shall be used only in continuous lengths without splice or tap. Hard service flexible cords No. 12 or larger may be repaired if spliced so that the splice retains the insulation, outer sheath properties, and usage characteristics of the cord being spliced. On or about July 17, 2012, the employer failed to ensure that flexible cords were continuous in length without splicing. Employees were using a spliced flexible cord as a power source for a DeWalt circular saw.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1926.405 G02 IV
- Issued
- Nov 1, 2012
- Abate by
- Nov 11, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.405(g)(2)(iv): Strain relief. Flexible cords shall be connected to devices and fittings so that strain relief is provided which will prevent pull from being directly transmitted to joints or terminal screws. On or about July 17, 2012, the employer failed to ensure that flexible cords had adequate strain relief. The flexible cord was used by employee(s) as a power source for a DeWalt circular saw.
Recent events (2)
- · I (S) $0
- · Z (S) $0
More inspections in this industry (NAICS 236116)
More inspections in LA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 335398186.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.