POPLAR BLUFF, MO —
OSHA Inspection: RICK'S WOODWORKING & CUSTOM CABINETS
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of RICK'S WOODWORKING & CUSTOM CABINETS in 2411 COUNTY ROAD 604, POPLAR BLUFF, MO 63901 (NAICS 337110). OSHA activity number 337348015.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- RICK'S WOODWORKING & CUSTOM CABINETS
- Site address
- 2411 COUNTY ROAD 604
- City
- POPLAR BLUFF
- State
- MO
- ZIP
- 63901
- Mailing
- 2422 COUNTY ROAD 604, POPLAR BLUFF, MO 63901
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337110
- Employees
- 4
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.22 A01
- Issued
- Nov 30, 2012
- Abate by
- Dec 27, 2012
- Penalty
- Initial $1,020 · Current $612 Reduced
General-duty citation text
29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms, and service rooms shall be kept clean and orderly and in a sanitary condition. 1. At the time of the inspection, the entire production area (woodworking) was dirty with saw dust and other debris. There was wood, saw dust, paper, cardboard and plastic all over the place. 2. At the time of the inspection, the paint room was in disorder. There was dust, wood, cardboard and paper cluttering the paint room.
Recent events (2)
- — I (S) $612
- — Z (S) $1020
1910.157 C01
- Issued
- Nov 30, 2012
- Abate by
- Dec 27, 2012
- Penalty
- Initial $1,020 · Current $0 Reduced
General-duty citation text
29 CFR 1910.157(c)(1): The employer shall provide portable fire extinguishers and shall mount, locate and identify them so that they are readily accessible to employees without subjecting the employees to possible injury. 1. In the production area, near the west wall, there were several (6 to 8) fire extinguishers situated (located) on the floor exposed to physical damage. There were no fire extinguishers hung up in the entire facility.
Recent events (2)
- — I (S) $0
- — Z (S) $1020
1910.178 L01 I
- Issued
- Nov 30, 2012
- Abate by
- Feb 11, 2013
- Penalty
- Initial $1,020 · Current $612 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(i): The employer shall ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l). 1. At the time of the inspection, there were two (2) employees (owner and shop foreman) operating a fork truck without training and/or certification to drive a fork truck.
Recent events (2)
- — I (S) $612
- — Z (S) $1020
1910.213 C01
- Issued
- Nov 30, 2012
- Abate by
- Dec 27, 2012
- Penalty
- Initial $1,020 · Current $612 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut but it shall not offer any considerable resistance to insertion of material to saw or to passage of the material being sawed. The hood shall be made of adequate strength to resist blows and strains incidental to reasonable operation, adjusting, and handling, and shall be so designed as to protect the operator from flying splinters and broken saw teeth. It shall be made of material that is soft enough so that it will be unlikely to cause tooth breakage. The hood shall be so mounted as to insure that its operation will be positive, reliable, and in true alignment with the saw; and the mounting shall be adequate in strength to resist any reasonable side thrust or other force tending to throw it out of line. 1. At the time of the inspection, in the production area, employees (owner and shop foreman) were using a hand-fed table saw to do rip cutting without the guard in place.
Recent events (2)
- — I (S) $612
- — Z (S) $1020
1910.213 D01
- Issued
- Nov 30, 2012
- Abate by
- Dec 27, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(d)(1): Each circular crosscut table saw shall be guarded by a hood which shall meet all the requirements of paragraph (c)(1) of this section for hoods for circular ripsaws. 1. At the time of the inspection, in the production area, employees (owner and shop foreman) were using a hand-fed table saw to do cross cutting without the guard in place.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections in this industry (NAICS 337110)
More inspections in MO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 337348015.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.