ITHACA, NY —
OSHA Inspection: GREENSPUN BUILDING AND DESIGN LLC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of GREENSPUN BUILDING AND DESIGN LLC in 100 RACHEL CARSON WAY TURQUOISE #10, ITHACA, NY 14850 (NAICS 238130). OSHA activity number 338232622.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- GREENSPUN BUILDING AND DESIGN LLC
- Site address
- 100 RACHEL CARSON WAY TURQUOISE #10
- City
- ITHACA
- State
- NY
- ZIP
- 14850
- Mailing
- 309 THIRD STREET, ITHACA, NY 14850
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 3
- Ownership type
- A
Citations
6 citations on file for this inspection.
1926.501 B13
- Issued
- Feb 15, 2013
- Abate by
- Feb 28, 2013
- Penalty
- Initial $2,800 · Current $250 Reduced
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system, nor were employee(s) provided with an alternative fall protection measure under another provision of paragraph 1926.501 (b): a) 100 Rachel Carson Way Turquois #10 - On or about 4 January, 2013 - Employees were installing framing material on the roof of a two story building without the use of personal fall protection.
Recent events (3)
- — J (S) $250
- — C (S) $2800
- — Z (S) $2800
1926.304 H01
- Issued
- Feb 15, 2013
- Abate by
- Feb 28, 2013
- Penalty
- Initial $2,800 · Current $250 Reduced
General-duty citation text
29 CFR 1926.304(h)(1): Each circular crosscut table saw was not guarded by a hood which completely enclosed that portion of the saw blade above the table and that portion of the saw above the material being cut: a) 100 Rachel Carson Way Turquois #10 - On or about 4 January, 2013 - Employees were using a table saw that was not guarded by a hood.
Recent events (3)
- — J (S) $250
- — C (S) $2800
- — Z (S) $2800
1926.304 G01
- Issued
- Feb 15, 2013
- Abate by
- Feb 28, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.304(g)(1): The sides of the lower blade were not guarded to the full diameter of the blade by a device that would automatically adjust itself to the thickness of the stock and remain in contact with stock being cut to give maximum protection a) 100 Rachel Carson Way Turquois #10 - On or about 4 January, 2013 - Employees were using a compound miter saw that was not equipped with a guard that automatically adjusted itself to the thickness of the stock and remain in contact with stock being cut to give maximum protection the full diameter of the blade.
Recent events (3)
- — J (S) $0
- — C (S) $0
- — Z (S) $0
1926.304 F
- Issued
- Feb 15, 2013
- Abate by
- Feb 28, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.304(f): Section 4.1.2(b) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f): Circular hand-fed rip saws were not equipped with a spreader to prevent material from squeezing the saw or being thrown back on the operator: a) 100 Rachel Carson Way Turquois #10 - On or about 4 January, 2013 - Employees were using a table saw that was not equipped with a spreader to prevent material from squeezing the saw or being thrown back on the operator.
Recent events (3)
- — J (S) $0
- — C (S) $0
- — Z (S) $0
1926.304 F
- Issued
- Feb 15, 2013
- Abate by
- Feb 28, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.304(f): Section 4.1.2(c) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f): Circular hand-fed rip saws did not have non-kickback fingers on dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: a) 100 Rachel Carson Way Turquois #10 - On or about 4 January, 2013 - Employees were using a table saw that did not have non-kickback fingers on dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator.
Recent events (3)
- — J (S) $0
- — C (S) $0
- — Z (S) $0
1926.403 B01
- Issued
- Feb 15, 2013
- Abate by
- Feb 28, 2013
- Penalty
- Initial $1,530 · Current $0 Reduced
General-duty citation text
29 CFR 1926.403(b)(1): Employer did not ensure that electrical equipment is free from recognized hazards that are likely to cause death or serious physical harm to employees: a) 100 Rachel Carson Way Turquois #10 - On or about 4 January, 2013 - Employees were using a compound miter saw that had a damaged external trigger guard housing exposing employees to electrical shock while engaging the operating switch.
Recent events (3)
- — J (S) $0
- — C (S) $1530
- — Z (S) $1530
More inspections in this industry (NAICS 238130)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 338232622.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.