OSHA Inspection: BLOUNT INTERNATIONAL, INC.

Issued

2013-03-19 00:00:00

Penalty

Initial $4250.00 · Current $2975.00 Reduced

General-duty citation text

29 CFR 1910.23(e)(1):     Standard railing(s) did not consist of top rail, intermediate rail and/or posts and/or did not have a vertical height of 42 inches (106.7 cm) nominal from upper surface of top rail to floor, platform runway, or ramp level:    (a) The Mill Platform/Mezzanine did not have an intermediate rail.

Issued

2013-03-19 00:00:00

Penalty

Initial $2550.00 · Current $1785.00 Reduced

General-duty citation text

29 CFR 1910.178(p)(1):     Powered industrial truck(s) found to be in need of repair, defective, or in any way unsafe had not been  taken out of service until restored to safe operating condition(s)    (a) The Yale Forklift # 3 did not have a nonslip surface on the brake pedal and was not taken out of service.

Issued

2013-03-19 00:00:00

Penalty

Initial $3400.00 · Current $2380.00 Reduced

General-duty citation text

29 CFR 1910.212(a)(1):     One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    (a) Maintenance Shop:  The Eisen/Bridgeport Mill did not have a guard to cover the unused portion of the bit and chuck above the material being worked.     (b) Maintenance Shop: The Progress Drill Press did not have a guard to cover the unused portion of the bit and chuck above the material being worked.    (c) Maintenance Shop: The Powermatic Drill Press did not have a guard to cover the unused portion of the bit and chuck above the material being worked.    (d) Maintenance Shop: The Dormac 180S lathe did not have a chuck guard.

Issued

2013-03-19 00:00:00

Abate by

2013-04-21 00:00:00

Penalty

Initial $3400.00 · Current $2380.00 Reduced

General-duty citation text

29 CFR 1910.215(b)(9):     The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch:    (a) Maintenance Shop: The Jet pedestal bench grinder's tongue guards on both side were both adjusted at greater than one fourth inch.

Issued

2013-03-19 00:00:00

Penalty

Initial $3400.00 · Current $2380.00 Reduced

General-duty citation text

29 CFR 1910.217(c)(2)(i)(a):     Point of operation guard(s) on mechanical power press(es) did not prevent entry of hands or fingers into the point of operation by reaching through, over, under or around the guard(s):    (a) Form Department: The AIDA 80 Machine #527, did not prevent entry of hands or fingers into the point of operation as there were three hairpin guards that were missing.

Issued

2013-03-19 00:00:00

Abate by

2013-04-21 00:00:00

Penalty

Initial $3400.00 · Current $2380.00 Reduced

General-duty citation text

29 CFR 1910.305(g)(2)(iii):     Flexible cords and cables were not connected to devices and fittings so that strain relief was provided that would prevent pull from being directly transmitted to joints or terminal screws:    (a) The three Die Carts by the USI Press 523, did not have adequate strain relief as where the electrical wiring was attached the outer insulation was broken exposing interior wiring.    (b) Forming Deparment: There was not adequate strain relief for the 2 hand control for the AIDA 2000, Machine # 506, as where the electrical wiring connected to the press the outer insulation was broken exposing interior wiring.