MADISON, NH —
OSHA Inspection: MADISON LUMBER MILL, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of MADISON LUMBER MILL, INC. in 71 MARCELLA DR., MADISON, NH 03849 (NAICS 321113). OSHA activity number 338946551.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MADISON LUMBER MILL, INC.
- Site address
- 71 MARCELLA DR.
- City
- MADISON
- State
- NH
- ZIP
- 03849
- Mailing
- P.O. BOX 224, WEST OSSIPEE, NH 03890
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321113
- Employees
- 50
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.265 C04 IV
- Issued
- May 7, 2013
- Penalty
- Initial $1,785 · Current $1,250 Reduced
General-duty citation text
29 CFR 1910.265(c)(4)(iv): Elevated walk(s) and runway(s), 4 feet or more from floor level, were not provided with a standard railing: (a) Plane mill - walkway along trim saw had an opening between the walkway and the bottom of the conveyor 7 inches wide and 24 inches deep.
Recent events (2)
- — I (S) $1249.5
- — Z (S) $1785
1910.265 C18 I
- Issued
- May 7, 2013
- Penalty
- Initial $2,231 · Current $1,562 Reduced
General-duty citation text
29 CFR 1910.265(c)(18)(i): Construction, operation, and maintenance of conveyors were not in accordance with Americaan National Standard B20.1-1957: As required by ANSI B20.1-1957, Part 1, Section 6, Paragraph 602, Pulley(s), sprocket(s), sheave(s), drum(s) and block(s) of conveyor(s) were not arranged to prevent the possibility of injury due to hands or parts of clothing being caught between the belt(s) and pulley(s) or chain(s) and sprocket(s): a. Chip belt conveyor - Employees shoveling spilled chips onto conveyor belt were exposed to unguarded belt and pulley. b. Plane mill - Employees near trim saw were exposed to pinch point of chain and sprocket not fully guarded.
Recent events (2)
- — I (S) $1561.7
- — Z (S) $2231
1910.36 H02
- Issued
- May 7, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.36(h)(2): Outdoor exit route was not covered where snow or ice was likely to accumulate. (Exception: Not required where employer can demonstrate that snow or ice will be removed before it can present a hazard) a. Office basement - Exit discharge was covered with snow and ice.
Recent events (2)
- — I (O) $0
- — Z (O) $0
1910.37 B02
- Issued
- May 7, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.37(b)(2): Each exit was not clearly visible and marked by a sign reading, Exit: a. Office basement - Door leading outside of basement to be used for emergencies was not labeled as an exit.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Madison Lumber Mill, INC.
View Madison Lumber Mill, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 321113)
More inspections in NH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 338946551.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.