WEATHERFORD, TX ·
OSHA Inspection: TERRY'S NEW DIMENSION MILLWORK
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of TERRY'S NEW DIMENSION MILLWORK in 1800 N MAIN, WEATHERFORD, TX 76085 (NAICS 337110). OSHA activity number 338958549.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TERRY'S NEW DIMENSION MILLWORK
- Site address
- 1800 N MAIN
- City
- WEATHERFORD
- State
- TX
- ZIP
- 76085
- Mailing
- 1800 N MAIN, WEATHERFORD, TX 76085
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337110
- Employees
- 16
- Ownership type
- Private (A)
Citations
6 citations on file for this inspection.
1910.212 A03 II
- Issued
- Apr 25, 2013
- Abate by
- May 16, 2013
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): The point of operation of machines whose operation exposed an employee to injury, was not guarded: On or about March 12, 2013, employees were exposed to injuries while using saws without guards in place. a. The guard on the Dewalt 12" chop saw had its guard held in place with a screw. b. The Makita 10" miter saw was missing the guard.
Recent events (2)
- · I (S) $960
- · Z (S) $1600
1910.213 C01
- Issued
- Apr 25, 2013
- Abate by
- May 16, 2013
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: On or about March 12, 2013, employees were exposed to amputation hazards while using the Powermatic table saws with unguarded blades.
Recent events (2)
- · I (S) $960
- · Z (S) $1600
1910.213 C02
- Issued
- Apr 25, 2013
- Abate by
- May 14, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator: On or about March 12, 2013, the Powermatic table saws were not equipped with a spreader. Employees were exposed to being struck by materials thrown back at them.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.213 C03
- Issued
- Apr 25, 2013
- Abate by
- May 14, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Handfed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: On or about March 12, 2013, non kickback fingers were not installed on the Powermatic table saws exposing employees to being struck by material being cut.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.303 G01
- Issued
- Apr 25, 2013
- Abate by
- May 16, 2013
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1910.303(g)(1): Sufficient access and working space was not provided and maintained about all electric equipment (operating at 600 volts, nominal, or less to ground) to permit ready and safe operation and maintenance of such equipment: On or about March 12, 2013, access to an electrical panel box was blocked by materials and equipment preventing ready and safe operation.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1910.141 A04 II
- Issued
- Apr 25, 2013
- Abate by
- May 16, 2013
- Penalty
- Initial $400 · Current $240 Reduced
General-duty citation text
29 CFR 1910.141(a)(4)(ii): Wastes were not collected and removed as often as necessary to maintain the place of employment in a sanitary condition: On or about March 12, 2013, saw dust was allowed to collect on the floor and other surfaces in the facility.
Recent events (2)
- · I (O) $240
- · Z (O) $400
More inspections at Terry'S NEW Dimension Millwork
View Terry'S NEW Dimension Millwork's full OSHA safety record →
More inspections in this industry (NAICS 337110)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 338958549.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.