CONVERSE, TX —
OSHA Inspection: MBCI
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of MBCI in 8677 INTERSTATE 10 EAST, CONVERSE, TX 78109 (NAICS 332311). OSHA activity number 339024747.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MBCI
- Site address
- 8677 INTERSTATE 10 EAST
- City
- CONVERSE
- State
- TX
- ZIP
- 78109
- Mailing
- PO BOX 69, CONVERSE, TX 78109
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332311
- Employees
- 852
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.212 A01
- Issued
- Aug 7, 2013
- Abate by
- Sep 10, 2013
- Penalty
- Initial $2,550 · Current $2,550
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: On or about April 25, 2013, employee(s) were exposed to struck by and point of operation hazards from the upswing of the folding beam on the Press Brake Machine, No serial plate, Jorns Press Norma Line, hydraulic, 480V. The operator controls the beam with a non-stationary foot pedal and was within the 14 inch diameter of the swing.
Recent events (2)
- — I (O) $2550
- — Z (S) $2550
1910.219 C04 I
- Issued
- Aug 7, 2013
- Abate by
- Aug 17, 2013
- Penalty
- Initial $3,400 · Current $0 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(i): Unguarded projecting shaft end(s) did not present a smooth edge and end and projected more than one half the diameter of the shaft: On or about April 25, 2013, employee was exposed to caught by hazards from a rotating shaft on the Sheet Line Machine, SN 30556, Bradbury RollFormer, 1996, the shaft projected approximately 1 3/4 inch and the diameter of the shaft was 2 3/4 inches.
Recent events (2)
- — I (S) $0
- — Z (S) $3400
1910.305 G01 IV A
- Issued
- Aug 7, 2013
- Abate by
- Aug 17, 2013
- Penalty
- Initial $3,400 · Current $0 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv)(A): Flexible cords and/or cables were used as a substitute for the fixed wiring of a structure: On or about April 25, 2013 employees were not protected from electrical hazards created by use of flexible cords and/or cables connected to the foot pedal to operate Air Shear Machine #4.
Recent events (2)
- — I (S) $0
- — Z (S) $3400
More inspections at Mbci
View Mbci's full OSHA safety record →
More inspections in this industry (NAICS 332311)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339024747.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.