SUGAR GROVE, IL —
OSHA Inspection: HFR PRECISION MACHINING, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of HFR PRECISION MACHINING, INC. in 1015 AIRPARK DRIVE, SUGAR GROVE, IL 60554 (NAICS 332710). OSHA activity number 339094211.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HFR PRECISION MACHINING, INC.
- Site address
- 1015 AIRPARK DRIVE
- City
- SUGAR GROVE
- State
- IL
- ZIP
- 60554
- Mailing
- 1015 AIRPARK DRIVE, SUGAR GROVE, IL 60554
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 43
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.147 C04 I
- Issued
- Aug 5, 2013
- Abate by
- Sep 20, 2013
- Penalty
- Initial $3,500 · Current $2,450 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: Facility: The employer has not developed and implemented specific procedures for each different machine that requires maintenance, repair, and set-up. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $2450
- — Z (S) $3500
1910.212 A01
- Issued
- Aug 5, 2013
- Abate by
- Aug 15, 2013
- Penalty
- Initial $3,500 · Current $2,450 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: Building 1011: Omada Vertical Saw unused portion of blade was not guarded. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $2450
- — Z (S) $3500
1910.215 A04
- Issued
- Aug 5, 2013
- Abate by
- Aug 15, 2013
- Penalty
- Initial $2,100 · Current $1,470 Reduced
General-duty citation text
29 CFR 1910.215(a)(4): Grinding machinery was not used with work rest(s) to support offhand grinding work. Tool Room: The Jet 8 inch Bench Grinder serial number 1012608B did not have a work rest installed on the right and left side to support the work. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $1470
- — Z (S) $2100
1910.215 B09
- Issued
- Aug 5, 2013
- Abate by
- Aug 15, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch: Tool Room: a. The Jet 8 inch Bench Grinder serial number 1012608B left tongue guard measured approximately one inch from the abrasive wheel. b. The Jet 8 inch Bench Grinder serial number 1012608B right tongue guard measured approximately one and five eight inches from the abrasive wheel. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E03 I
- Issued
- Aug 5, 2013
- Abate by
- Aug 15, 2013
- Penalty
- Initial $2,100 · Current $1,470 Reduced
General-duty citation text
29 CFR 1910.219(e)(3)(i): Vertical or inclined belt(s) were not enclosed by guard(s) conforming to the requirements specified at 29 CFR 1910.219(m) and (o): Tool Room: Employees were exposed to the in running nip point of the unguarded horizontal belt and pulley on the Mead Belt Sander. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $1470
- — Z (S) $2100
1910.1200 H01
- Issued
- Aug 5, 2013
- Abate by
- Sep 20, 2013
- Penalty
- Initial $2,100 · Current $1,470 Reduced
General-duty citation text
29 CFR 1910.1200(h)(1): Employees were not provided effective information and training on hazardous chemicals in their work area at the time of their initial assignment and whenever a new hazard that the employees had not been previously trained about was introduced into their work area: Facility: Employees working with chemicals such as but not, limited to coolants and lubricants were inadequately trained on the safety and health hazards. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $1470
- — Z (S) $2100
More inspections at HFR Precision Machining, INC.
View HFR Precision Machining, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339094211.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.