SUWANEE, GA ·
OSHA Inspection: RIGOBERTO GONZALEZ GUTIERREZ
Unprogrammed Other inspection · Safety discipline
At a glance
On , OSHA opened an unprogrammed Other safety inspection of RIGOBERTO GONZALEZ GUTIERREZ in 1255 GALLATIN WAY LOT 39, SUWANEE, GA 30024 (NAICS 238130). OSHA activity number 339304834.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- RIGOBERTO GONZALEZ GUTIERREZ
- Site address
- 1255 GALLATIN WAY LOT 39
- City
- SUWANEE
- State
- GA
- ZIP
- 30024
- Mailing
- 2218 WOOD TERRACE RDG, DORAVILLE, GA 30340
What kind of inspection was it?
- Inspection type
- Unprogrammed Other (I)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 3
- Ownership type
- A
Citations
6 citations on file for this inspection.
1926.100 A
- Issued
- Nov 12, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1926.100(a): Employees working in areas where there was a possible danger of head injury from impact, or falling or flying objects, or from electrical shock and burns, were not protected by protective helmets: On or about August 15, 2013, at 1255 Gallatin Way, Suwanee, Georgia: An employee performing framing work was exposed to struck-by hazards from falling tools, nails, and plywood, from the employee working above him when he did not use a hard hat.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1926.102 A01
- Issued
- Nov 12, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1926.102(a)(1): Eye and face protective equipment were not used when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents. On or about August 15, 2013, at 1255 Gallatin Way, Suwanee, Georgia: An employee performing framing work was exposed to struck-by hazards from sawdust, and wood chips, when he used a Makita 5007F circular saw without using eye protection.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1926.304 G01
- Issued
- Nov 12, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $2,000 · Current $1,200 Reduced
General-duty citation text
29 CFR 1926.304(g)(1): The sides of the lower blade were not guarded to the full diameter of the blade by a device that would automatically adjust itself to the thickness of the stock and remain in contact with stock being cut to give maximum protection: On or about August 15, 2013, at 1255 Gallatin Way, Suwanee, Georgia: An employee performing framing work was exposed to amputation hazards when he used a Makita 5007F radial saw with a piece of wood wedged between the cover and the blade to bypass the lower blade guard.
Recent events (2)
- · I (S) $1200
- · Z (S) $2000
1926.404 F06
- Issued
- Nov 12, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1926.404(f)(6): The path to ground from circuits, equipment, or enclosures was not permanent and continuous: On or about August 15, 2013, at 1255 Gallatin Way, Suwanee, Georgia: An employee performing framing work was exposed to mild electric shock hazards when he used a Makita 5007F, 115 volt, 15 amp, circular saw powered by an extension cord with a missing ground pin.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1926.405 G02 IV
- Issued
- Nov 12, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.405(g)(2)(iv): Flexible cords were not connected to devices and fittings so that strain relief is provided to prevent pull from being directly transmitted to joints or terminal screws: On or about August 15, 2013, at 1255 Gallatin Way, Suwanee, Georgia: An employee performing framing work was exposed to mild electric shock hazards when he used a Makita 5007F, 115 volt, 15 amp circular saw powered by an extension cord with strain relief damage to the plug.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1926.416 E01
- Issued
- Nov 12, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.416(e)(1): Worn or frayed electric cords or cables were used: On or about August 15, 2013, at 1255 Gallatin Way, Suwanee, Georgia: An employee performing framing work was exposed to mild electric shock hazards when he used a Makita 5007F, 115 volt, 15 amp, circular saw powered using an extension cord that was cut and had the outer sheathing missing iin several places.
Recent events (2)
- · I (S) $0
- · Z (S) $0
More inspections in this industry (NAICS 238130)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339304834.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.