OSHA Inspection: INTEGRITY CABINETS, LLC.

Issued

Sep 25, 2013

Abate by

Oct 15, 2013

Penalty

Initial $4,590 · Current $2,500 Reduced

General-duty citation text

29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section:    a) On or about August 21, 2013 - Sanding department, specific procedures had not been developed for equipment such as but not limited to the, Butfering Optima Sto 313 and Biesse Rover A3.65 for employees performing maintenance.

Issued

Sep 25, 2013

Abate by

Nov 15, 2013

Penalty

Initial $4,590 · Current $2,500 Reduced

General-duty citation text

29 CFR 1910.147(c)(7)(i): The employer did not provide adequate training to ensure that the purpose and function of the energy control program was understood by employees:    a) On or about August 21, 2013 - Sanding department, employees were not trained to recognize and minimize hazards associated with controlling energy when performing service and maintenance activities.

Issued

Sep 25, 2013

Abate by

Oct 14, 2013

Penalty

Initial $3,060 · Current $1,750 Reduced

General-duty citation text

29 CFR 1910.178(l)(1)(i): The employer did not ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l):    a) On or about August 21, 2013 - Facility, employees operating a Toyota Model#8FGCU25, S/N#11039 powered industrial truck had not been trained and evaluated.

Issued

Sep 25, 2013

Abate by

Oct 15, 2013

Penalty

Initial $3,060 · Current $1,750 Reduced

General-duty citation text

29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut:    a) On or about August 21, 2013 - Accessory department, employees were operating equipment such as but not limited to a Powermatic 10 inch table saw, Model#b6-7A Saw, S/N#0702066065 without a guard over the blade.

Issued

Sep 25, 2013

Abate by

Oct 7, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator.  Note:  The spreader in connection with grooving, dadoing or rabbeting is not required.  a) On or about August 21, 2013 - Accessory department, employees were operating equipment such as but not limited to a Powermatic 10 inch table saw, Model#b6-7A Saw, S/N#0702066065 without a spreader bar behind the blade.

Issued

Sep 25, 2013

Abate by

Oct 7, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator:  a) On or about August 21, 2013 - Accessory department, employees were operating equipment, such as but not limited to, a Powermatic 10 inch table saw, Model#b6-7A Saw, S/N#0702066065 without non-kickback fingers.

Issued

Sep 25, 2013

Abate by

Oct 15, 2013

Penalty

Initial $4,590 · Current $2,500 Reduced

General-duty citation text

29 CFR 1910.213(p)(4): Belt sanding machinery was not provided with a guard at each nip point where the sanding belt ran onto a pulley, to prevent the operator's hands or fingers from coming into contact with nip points:     a) On or about August 21, 2013 - Accessory department, a Birmingham edge sander was being operated with nip points exposed.

Issued

Sep 25, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(g)(1): Sufficient access and working space was not provided and maintained about all electric equipment (operating at 600 volts, nominal, or less to ground) to permit ready and safe operation and maintenance of such equipment:  a) On or about August 21, 2013 - Accessory department, a box, pallet of products, and scrap lumber were being stored in front of an electrical panel.