EAST SYRACUSE, NY —
OSHA Inspection: MORSE MANUFACTURING COMPANY, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of MORSE MANUFACTURING COMPANY, INC. in 727 WEST MANLIUS STREET, EAST SYRACUSE, NY 13057 (NAICS 333924). OSHA activity number 339436164.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MORSE MANUFACTURING COMPANY, INC.
- Site address
- 727 WEST MANLIUS STREET
- City
- EAST SYRACUSE
- State
- NY
- ZIP
- 13057
- Mailing
- PO BOX 518, EAST SYRACUSE, NY 13057
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333924
- Employees
- 40
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Jan 24, 2014
- Penalty
- Initial $2,800 · Current $1,680 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being struck by the load should the load slip off the hook, or the lifting device fails: a) Rotating Area, on or about 10/22/13: A 1/4 ton Dayton overhead hoist being lift rotators on a pallet was missing the safety latche.
Recent events (2)
- — I (S) $1680
- — Z (S) $2800
1910.22 A01
- Issued
- Jan 24, 2014
- Penalty
- Initial $2,100 · Current $1,260 Reduced
General-duty citation text
29 CFR 1910.22(a)(1): Place(s) of employment were not kept clean: a) Receiving Area, on or about 10/22/13: Explosive Wood Dust (Class II) was observed throughout the floor area where the Sears Craftsman Radial Arm Saw is used.
Recent events (2)
- — I (S) $1260
- — Z (S) $2100
1910.147 C01
- Issued
- Jan 24, 2014
- Abate by
- Feb 28, 2014
- Penalty
- Initial $3,500 · Current $2,100 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of energy control procedures, employee training, and periodic inspections to ensure that before any employee performing any servicing or maintenance on a machine or equipment where the unexpected energizing, start up or release of stored energy could occur and cause injury, the machine or equipment would be isolated from the energy source and rendered inoperative. a) Morse Manufacturing Company, Inc., on or about 11/20/13: The employer had not established an energy control program consisting of energy control procedures, employee training and periodic inspections for employees who perform servicing and/or maintenance on various machinery or equipment such as but not limited to: CNC Machiines; Scottsman Saw and Wells Saw.
Recent events (2)
- — I (S) $2100
- — Z (S) $3500
1910.213 H01
- Issued
- Jan 24, 2014
- Penalty
- Initial $2,800 · Current $1,680 Reduced
General-duty citation text
29 CFR 1910.213(h)(1): The sides of the lower exposed portion of the blade of radial saw(s) were not guarded to the full diameter of the blade by a device that automatically adjusted itself to the thickness of the stock and remained in contact with the matetrial being cut: a) Receiving Area, on or about 10/22/13: Craftsman Radial Saw had no lower blade guard on either side of blade.
Recent events (2)
- — I (S) $1680
- — Z (S) $2800
1910.213 H04
- Issued
- Jan 24, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(h)(4): Radial saw(s) were not installed in a manner so as to cause the cutting head to return gently to the starting position when released by the operator: a) Receiving Area, on or about 10/22/13: Craftsman Radial Arm Saw did not return to the starting position when released.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Morse Manufacturing Company, INC.
View Morse Manufacturing Company, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333924)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339436164.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.