PENSACOLA, FL ·
OSHA Inspection: D & M TRUSS CO.
Complaint inspection · Health discipline
At a glance
On , OSHA opened a complaint health inspection of D & M TRUSS CO. in 2620 W MICHIGAN AVE., PENSACOLA, FL 32526 (NAICS 321214). OSHA activity number 339440984.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- D & M TRUSS CO.
- Site address
- 2620 W MICHIGAN AVE.
- City
- PENSACOLA
- State
- FL
- ZIP
- 32526
- Mailing
- PO BOX 37385, PENSACOLA, FL 32526
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321214
- Employees
- 19
- Ownership type
- Private (A)
Citations
5 citations on file for this inspection.
1910.147 C06 I
- Issued
- Dec 16, 2013
- Abate by
- Feb 4, 2014
- Penalty
- Initial $2,000 · Current $1,200 Reduced
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed: a. On or about October 25, 2013, the employer had not conducted annual or more frequent inspections of the energy control procedures.
Recent events (2)
- · I (S) $1200
- · Z (S) $2000
1910.147 C07 I
- Issued
- Dec 16, 2013
- Abate by
- Feb 4, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i): The employer did not provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees: a. On or about October 25, 2013, the employer did not provide training to all authorized, affected, and other employees with the purpose and functions of the energy control program.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.213 B01
- Issued
- Dec 16, 2013
- Abate by
- Feb 4, 2014
- Penalty
- Initial $2,000 · Current $1,200 Reduced
General-duty citation text
29 CFR 1910.213(b)(1): Woodworking machine(s) were not provided with mechanical or electrical power controls so located that the operator could cut off the power from the machine without leaving his position at the point of operation: a. On or about October 25, 2013, Saw Shed #1, the Monet Web Saw was not equipped with an emergency stop at the operator's position.
Recent events (2)
- · I (S) $1200
- · Z (S) $2000
1910.213 R04
- Issued
- Dec 16, 2013
- Abate by
- Feb 4, 2014
- Penalty
- Initial $2,800 · Current $1,680 Reduced
General-duty citation text
29 CFR 1910.213(r)(4): Suitable guards were not provided to reduce to a minimum the hazard due to the point of operation of the Clary Short Cutter Top and Bottom Saw and Monet Web Saw: a. On or about October 25, 2013, Saw Shed #1, Monet Web Saw did not have an adequate guard, exposing employees to the hazard of being cut by the saw blade. b. On or about October 25, 2013, Saw Shed #2, Clary Short Cutter Top and Bottom Saw did not have an adequate guard, exposing employees to the hazard of being cut by the saw blade.
Recent events (2)
- · I (S) $1680
- · Z (S) $2800
1910.219 F03
- Issued
- Dec 16, 2013
- Abate by
- Feb 4, 2014
- Penalty
- Initial $2,400 · Current $1,440 Reduced
General-duty citation text
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven -7 feet or less above floors or platforms were not enclosed: a. On or about October 25, 2013, Saw Shed #2, at the operators station of the Clary Short Cutter Top and Bottom Saw, the 5-inch sprocket and chain did not have a guard, exposing employees to the hazard of being caught by the sprocket.
Recent events (2)
- · I (S) $1440
- · Z (S) $2400
More inspections in this industry (NAICS 321214)
More inspections in FL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 339440984.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.