SALTILLO, MS ·
OSHA Inspection: LIBERTY TIRE RECYCLING LLC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of LIBERTY TIRE RECYCLING LLC in 2058 HWY 145, SALTILLO, MS 38866 (NAICS 423930). OSHA activity number 339479859.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- LIBERTY TIRE RECYCLING LLC
- Site address
- 2058 HWY 145
- City
- SALTILLO
- State
- MS
- ZIP
- 38866
- Mailing
- 2058 HWY 145, SALTILLO, MS 38866
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 423930
- Employees
- 31
- Ownership type
- Private (A)
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Nov 22, 2013
- Abate by
- Dec 9, 2013
- Penalty
- Initial $4,250 · Current $2,000 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees, in that, employees were exposed to struck by hazard: (a) Facility - On or about November 06, 2013 John Deere 644E front end loader and John Deere front end loader 444J did not have audible back-up alarms.
Recent events (2)
- · I (S) $2000
- · Z (S) $4250
1910.23 C01
- Issued
- Nov 22, 2013
- Penalty
- Initial $2,550 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.23(c)(1): Every open-sided floor or platform 4 feet or more above adjacent floor or ground level shall be guarded by a standard railing (or the equivalent as specified in paragraph (e)(3) of this section) on all open sides except where there is entrance to a ramp, stairway, or fixed ladder. The railing shall be provided with a toeboard wherever, beneath the open sides, (a) Shredder No. 3 and Shredder No. 4 - On or about November 06, 2013 catwalks were missing an end guardrail. Shredder No. 3 was 5 feet 02 inches above floor. Shredder No. 4 was 7 feet 05 inches above floor.
Recent events (2)
- · I (O) $1500
- · Z (S) $2550
1910.23 D01 III
- Issued
- Nov 22, 2013
- Abate by
- Jan 8, 2014
- Penalty
- Initial $3,400 · Current $2,500 Reduced
General-duty citation text
29 CFR 1910.23(d)(1)(iii): On stairways less than 44 inches wide having both sides open, one stair railing on each side. (a) Shedder No. 1 - On or about November 06, 2013 the 5 rung x 30 inch wide x 39 inch high stairway was missing the stair railing on one side.
Recent events (2)
- · I (S) $2500
- · Z (S) $3400
1910.23 E01
- Issued
- Nov 22, 2013
- Abate by
- Jan 8, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.23(e)(1): A standard railing shall consist of top rail, intermediate rail, and posts, and shall have a vertical height of 42 inches nominal from upper surface of top rail to floor, platform, runway, or ramp level. The top rail shall be smooth-surfaced throughout the length of the railing. The intermediate rail shall be approximately halfway between the top rail and the floor, platform, runway, or ramp. The ends of the rails shall not overhang the terminal posts except where such overhang does not constitute a projection hazard. (a) Facility - On or about November 06, 2013 the following open sided stairs did not have standard railing: (i) Shredder No. 4 - One rail on each stair side (ii) Shredder No. 1 - One rail on right side of stair
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.178 L06
- Issued
- Nov 22, 2013
- Abate by
- Dec 23, 2013
- Penalty
- Initial $2,550 · Current $0 Reduced
General-duty citation text
29 CFR 1910.178(l)(6): Certification. The employer shall certify that each operator has been trained and evaluated as required by this paragraph (l). The certification shall include the name of the operator, the date of the training, the date of the evaluation, and the identity of the person(s) performing the training or evaluation. (a) Facility - On or about November 06, 2013 forklift operators have not been certified by the employer.
Recent events (2)
- · I (S) $0
- · Z (S) $2550
1910.219 C04 I
- Issued
- Nov 22, 2013
- Penalty
- Initial $2,550 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(i): Projecting shaft ends shall present a smooth edge and end and shall not project more than one-half the diameter of the shaft unless guarded by nonrotating caps or safety sleeves. (a) Shredder No. 3 Conveyor - On or about November 06, 2013 a rotating shaft end was not guarded.
Recent events (2)
- · I (S) $1500
- · Z (S) $2550
More inspections at Liberty Tire Recycling LLC
View Liberty Tire Recycling LLC's full OSHA safety record →
More inspections in this industry (NAICS 423930)
More inspections in MS
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 339479859.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.