OGEMA, WI ·
OSHA Inspection: BADGER PRECISION CUT STOCK
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of BADGER PRECISION CUT STOCK in W 4995 BJORKLUND RD, OGEMA, WI 54459 (NAICS 321920). OSHA activity number 339495418.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BADGER PRECISION CUT STOCK
- Site address
- W 4995 BJORKLUND RD
- City
- OGEMA
- State
- WI
- ZIP
- 54459
- Mailing
- W 4995 BJORKLUND RD, OGEMA, WI 54459
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321920
- Employees
- 23
- Ownership type
- Private (A)
Citations
4 citations on file for this inspection.
1910.219 C02 I
- Issued
- Feb 6, 2014
- Abate by
- Feb 21, 2014
- Penalty
- Initial $1,700 · Current $1,020 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: (a) Throughout the facility; Rotating shafts were not guarded, such as, but not limited to: (1) GoFast/McDonough Area; The open shaft east side of the GoFast Saw, and (2) Mill Area; The open shaft on the north side the GoFast Saw.
Recent events (2)
- · I (S) $1020
- · Z (S) $1700
1910.219 I02
- Issued
- Feb 6, 2014
- Abate by
- Feb 21, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(i)(2): Revolving surfaces of shaft coupling(s) were not covered by a safety sleeve: (a) GoFast/McDonough Area; Rotating couplers were not guarded, such as, but not limited to: (1) GoFast Saw; The two inch rotating coupler on the east side of the GoFast Saw, and (2) GoFast saw; The band saw drive coupler on the west side of the GoFast Saw.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.95 E
- Issued
- Feb 6, 2014
- Abate by
- Feb 28, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.95(e): The employer did not notify each employee exposed at or above an 8-hour time-weighted average of 85 decibels of the results of the monitoring: (a) Badger Precision Cut Stock, throughout the production area; The employer did not notify the employees of the decibel levels obtained in each area that was above the 85 dBA TWA requirement.
Recent events (2)
- · I (O) $0
- · Z (O) $0
1910.147 C07 IV
- Issued
- Feb 6, 2014
- Abate by
- Feb 21, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(iv): The employer did not certify that LOTO employee training had been accomplished and kept up to date: (a) Badger Precision Cut Stock, Administrate Office: The employer did not certify the authorized and affected employee lockout tagout training.
Recent events (2)
- · I (O) $0
- · Z (O) $0
More inspections at Badger Precision CUT Stock
View Badger Precision CUT Stock's full OSHA safety record →
More inspections in this industry (NAICS 321920)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 339495418.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.