WASHINGTON, DC —
OSHA Inspection: ENCORE CONSTRUCTION, INC.
Unprogrammed Other inspection · Safety discipline
At a glance
On , OSHA opened an unprogrammed Other safety inspection of ENCORE CONSTRUCTION, INC. in 433 MASSACHUSETTS AVENUE, NW, WASHINGTON, DC 20003 (NAICS 236220). OSHA activity number 339512378.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ENCORE CONSTRUCTION, INC.
- Site address
- 433 MASSACHUSETTS AVENUE, NW
- City
- WASHINGTON
- State
- DC
- ZIP
- 20003
- Mailing
- 2014 RENARD COURT SUITE J, ANNAPOLIS, MD 21401
What kind of inspection was it?
- Inspection type
- Unprogrammed Other (I)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 236220
- Employees
- 1
- Ownership type
- A
Citations
3 citations on file for this inspection.
1926.102 A01
- Issued
- Jan 30, 2014
- Penalty
- Initial $1,600 · Current $1,600
General-duty citation text
29 CFR 1926.102(a)(1): Eye and face protective equipment were not used when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents: a) Exterior Front Sidewalk - A carpenter was observed cutting one half inch wood trim on a DeWalt electric table saw, model number DW745, serial number 2009-42CT023596, and was not wearing eye protection, on or about 12/05/2013. For the purposes of this inspection, this employer was determined to be the controlling and correcting employer of the jobsite. The employer is being cited under OSHA's Multi-Employer Workplace Policy.
Recent events (2)
- — I (O) $1600
- — Z (S) $1600
1926.304 F
- Issued
- Jan 30, 2014
- Penalty
- Initial $2,000 · Current $1,340 Reduced
General-duty citation text
29 CFR 1926.304(f): All woodworking tools and machinery did not meet applicable requirements of American National Standards Institute (ANSI), 01.1-1961, Safety Code for Woodworking Machinery. Section 4.1.2(c) of ANSI 01.1-1961, Safety Code for Woodworking Machinery: Circular hand-fed rip saws did not have non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: a) Exterior Front Sidewalk - A carpenter was observed using a DeWalt table saw, model number DW475, serial number 2009-42CT023596, to cut one half inch thick door trim and non-kickback dogs were not provided, on or about 12/05/2013. Section 4.1.2(b) of ANSI 01.1-1961, Safety Code for Woodworking Machinery: Circular hand-fed rip saws were not equipped with a spreader to prevent material from squeezing the saw or being thrown back on the operator: b) Exterior Front Sidewalk - A carpenter was observed using a DeWalt table saw, model number DW475, serial number 2009-42CT023596, to cut one half inch thick door trim and a spreader was not provided, on or about 12/05/2013. Section 3.1.3(c) of ANSI 01.1-1961, Safety Code for Woodworking Machinery: Provisions were not made to prevent wood-working machine(s) from automatically restarting upon restoration of power after power failure: c) Exterior Front Sidewalk - A carpenter was observed using a DeWalt table saw, modell number DW475, serial number 2009-42CT023596, to cut a one half inch thick door trim and a magnetic restart switch was not provided, on or about 12/05/2013. For the purposes of this inspection, this employer was determined to be the controlling and correcting employer of the jobsite. The employer is being cited under OSHA's Multi-Employer Workplace Policy.
Recent events (2)
- — I (S) $1340
- — Z (S) $2000
1926.304 I01
- Issued
- Jan 30, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.304(i)(1): Each circular hand-fed ripsaw was not guarded by a hood which completely enclosed that portion of the saw above the table and that portion of the saw above the material being cut: a) Exterior Front Sidewalk - A carpenter was observed using a DeWalt table saw, model number DW475, serial number 2009-42CT023596, to cut one half inch thick wood door trim and a hood guard was not provided, on or about 12/05/2013.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Encore Construction, INC.
View Encore Construction, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 236220)
More inspections in DC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339512378.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.