MCDONOUGH, GA ·
OSHA Inspection: DICKERSON CUSTOM CABINETS, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of DICKERSON CUSTOM CABINETS, INC. in 127 MT. CARMEL RD, MCDONOUGH, GA 30253 (NAICS 321918). OSHA activity number 339555039.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- DICKERSON CUSTOM CABINETS, INC.
- Site address
- 127 MT. CARMEL RD
- City
- MCDONOUGH
- State
- GA
- ZIP
- 30253
- Mailing
- 289 JONESBORO ROAD SUITE 251, MCDONOUGH, GA 30253
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321918
- Employees
- 12
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.213 C01
- Issued
- May 7, 2014
- Abate by
- Jun 30, 2014
- Penalty
- Initial $2,800 · Current $1,680 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood, which completely enclosed that portion of the saw above the table and above the material being cut. On or about 1/9/2014 at 127 Mt. Carmel Road, McDonough, GA: a. Shop area - Employees were using a Powermatic, Model 66, SN# 0966854 table saw without the guard for the portion of the saw above the table. b. Shop area - Employees were using a Grizzly G1023S10" Table Saw, SN # 077032 table saw without the guard for the portion of the saw above the table. c. Shop area - Employees were using a Powermatic, Model 66, SN# 92662341 table saw without the guard for the portion of the saw above the table. d. Shop area - Employees were using a JET, Model JTAS 10-1, SN# 7097014 table saw without the guard for the portion of the saw above the table.
Recent events (2)
- · I (S) $1680
- · Z (S) $2800
1910.213 C02
- Issued
- May 7, 2014
- Abate by
- Jun 30, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. On or about 01/09/2014 at 127 Mt. Carmel Road, McDonough, GA: a. Shop area - Employees were using a Powermatic, Model 66, SN# 0966854 table saw without having the spreader attached to the saw, preventing material from being thrown back on the operator. b. Shop area - Employees were using a Grizzly G1023S10" Table Saw, SN # 077032 table saw without having the spreader attached to the saw, preventing material from being thrown back on the operator.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.213 C03
- Issued
- May 7, 2014
- Abate by
- Jun 30, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. On or about 01/09/2014 at 127 Mt. Carmel Road, McDonough, GA: a. Shop area - Employees were using a Powermatic, Model 66, SN# 0966854 table saw without having the non-kickback fingers to prevent material from being thrown toward the operator. b. Shop area - Employees were using a Grizzly G1023S10" Table Saw, SN # 077032 table saw without having the non-kickback fingers to prevent material from being thrown toward the operator.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.106 D06 III
- Issued
- May 7, 2014
- Abate by
- Jun 3, 2014
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1910.106(d)(6)(iii): "Spill containment." The storage area was not graded in a manner to divert possible spills away from buildings or other exposures nor was it surrounded by a curb at least 6 inches high. When curbs are used, provisions were not made for draining of accumulations of ground or rainwater or spills of flammable liquids. Drains did not terminate at a safe location and were not accessible to operation under fire conditions. On or about 01/09/2014 at 127 Mt. Carmel Road, McDonough, GA: The storage area where flammable paints and lacquers were kept was not graded, curbed, or bermed in such a manner that flammable liquids would not drain off site.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
1910.106 D07 I A
- Issued
- May 7, 2014
- Abate by
- Jun 3, 2014
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1910.106(d)(7)(i)(a): At least one portable fire extinguisher having a rating of not less than 12-B units was not located outside of, but not more than 10 feet from, the door opening into any room used for storage. On or about 01/09/2014 at 127 Mt. Carmel Road, McDonough, GA: In the storage area where flammable paints and lacquers were kept, a portable fire extinguisher having a rating not less that 12-B was not provided. Employees are exposed to a smoke inhalation and fire hazard.
Recent events (2)
- · I (S) $720
- · Z (S) $1200
More inspections at Dickerson Custom Cabinets, INC.
View Dickerson Custom Cabinets, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 321918)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339555039.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.