OSHA Inspection: ALL MARBLE, GRANITE & TILE IMPORTS, INC.

Issued

Apr 8, 2014

Penalty

Initial $1,200 · Current $900 Reduced

General-duty citation text

29 CFR 1910.134(e)(1): The employer did not provide a medical evaluation to determine the employee's ability to use a respirator, before the employee was fit tested or required to use the respirator in the workplace:   a) Production Area: On or about 01/15/2014, the employer did not provide medical evaluations to employees who wore the Gerson (M#8311P) half mask respirators.

Issued

Apr 8, 2014

Penalty

Initial $1,600 · Current $1,200 Reduced

General-duty citation text

29 CFR 1910.178(l)(1)(ii): The employer did not ensure that each operator had successfully completed the training required by paragraph (l), except as permitted by paragraph (l)(5), prior to permitting an employee to operate a powered industrial truck:   a) Production Area: On or about 01/15/2014, the employer did not ensure that each operator of the Nissan (M#:MCUL02A30LV) propane powered forklift truck had successfully completed forklift training.

Issued

Apr 8, 2014

Penalty

Initial $1,200 · Current $900 Reduced

General-duty citation text

29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling:   a) Profile Room Panel box C: On or about 01/15/2014, non-approved circuit breakers were used daily to operate the overhead lights, exhaust fans and overhead heaters.    b) Profile Room Panel box B: On or about 01/15/2014, non-approved circuit breakers were used daily to operate the overhead lights, the CNC machine and overhead heaters.    c) CNC Room Panel Box A: On or about 01/15/2014, non-approved circuit breakers were used daily to operate the overhead lights, electrical receptacles and overhead heaters.

Issued

Apr 8, 2014

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(g)(1)(ii): The required working space about electric equipment rated 600 volts, nominal, or less to ground, was used for storage:    a) Profile Room-Panel "C": On or about 01/15/2014, the working space about Electrical Panel "C" was used for the storage of equipment such as, but not limited to stone slabs, tools, and A-frame freight racks.  b) Profile Room- Panel "B": On or about 01/15/2014, the working space about Electrical Panel "B" was used for the storage of equipment such as, but not limited to stone slabs, tools, and A-frame freight racks.  c) CNC Room-Panel "A": On or about 01/15/2014, the working space about Electrical Panel "A" was used for the storage of equipment/supplies such as, but not limited to stone slabs, tools, and A-frame freight racks.

Issued

Apr 8, 2014

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.134(c)(2): The employer did not develop and implement a respiratory protection program in accordance with sections i and ii of this paragraph (c)(2) for employees who chose to wear respirators where respirator use was not required:   a) Production Area: On or about 01/15/2014, the employer did not establish nor implement the provisions of a written respiratory protection program before allowing the use of respiratory protection such as, but not limited to the Gerson (M#8311P) half mask respirators worn by employees performing stonecutting/polishing operations at the facility.

Issued

Apr 8, 2014

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(f)(2): Each service, feeder, and branch circuit, at its disconnecting means or overcurrent device, was not legibly marked to indicate its purpose, nor located and arranged so the purpose was evident:    a) Production Area-Profile Room:  On or about 01/15/2014, the employer did not label the electrical panel circuit breakers for Panel "C"to indicate their purpose.   b) Production Area- Profile Room: On or about 01/15/2014, the employer did not label the electrical panel circuit breakers for Panel "B" to indicate their purpose.   c) Production Area-CNC Room: on or about 01/15/2014, the employer did not label the electrical panel circuit breakers for Panel "A" to indicate their purpose.