GREENFIELD, OH ·
OSHA Inspection: C-MOLD, LLC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of C-MOLD, LLC in 175 INDUSTRIAL PARK DR., GREENFIELD, OH 45123 (NAICS 326160). OSHA activity number 339561490.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- C-MOLD, LLC
- Site address
- 175 INDUSTRIAL PARK DR.
- City
- GREENFIELD
- State
- OH
- ZIP
- 45123
- Mailing
- 175 INDUSTRIAL PARK DR., GREENFIELD, OH 45123
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 326160
- Employees
- 45
- Ownership type
- Private (A)
Citations
5 citations on file for this inspection.
1910.23 C01
- Issued
- Apr 1, 2014
- Abate by
- Apr 25, 2014
- Penalty
- Initial $2,800 · Current $1,400 Reduced
General-duty citation text
29 CFR 1910.23(c)(1): Every open-sided floor or platform 4 feet or more above adjacent floor or ground level shall be guarded by a standard railing (or the equivalent as specified in paragraph (e)(3) of this section) on all open sides except where there is entrance to a ramp, stairway, or fixed ladder. The railing shall be provided with a toeboard wherever, beneath the open sides, a) Open sided platform going to the top of the injection molding machines #2 and #3 were not equipped with a midrail.
Recent events (2)
- · I (S) $1400
- · Z (S) $2800
1910.24 H
- Issued
- Apr 1, 2014
- Abate by
- May 16, 2014
- Penalty
- Initial $2,800 · Current $1,400 Reduced
General-duty citation text
29 CFR 1910.24(h): "Railings and handrails." Standard railings shall be provided on the open sides of all exposed stairways and stair platforms. Handrails shall be provided on at least one side of closed stairways preferably on the right side descending. Stair railings and handrails shall be installed in accordance with the provisions of 1910.23. a) Set of stairs attached to the rear of the injection molding machines #2 and #3 were without a complete hand railing system.
Recent events (2)
- · I (S) $1400
- · Z (S) $2800
1910.26 A03 VII
- Issued
- Apr 1, 2014
- Penalty
- Initial $2,100 · Current $1,050 Reduced
General-duty citation text
29 CFR 1910.26(a)(3)(vii): The bottoms of the four rails are to be supplied with insulating non-slip material for the safety of the user. a) Portable metal ladders at the injection molding machines were not equipped with non-slip footing to prevent movement as employeees use to gain ascess to machines exposings them to falls.
Recent events (2)
- · I (S) $1050
- · Z (S) $2100
1910.178 L01 II
- Issued
- Apr 1, 2014
- Penalty
- Initial $2,800 · Current $1,400 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(ii): Prior to permitting an employee to operate a powered industrial truck (except for training purposes), the employer shall ensure that each operator has successfully completed the training required by this paragraph (l), except as permitted by paragraph (l)(5). a) Operators of powered industrial trucks were not trained prior to being allowed to operate a forklift.
Recent events (2)
- · I (S) $1400
- · Z (S) $2800
1910.242 B
- Issued
- Apr 1, 2014
- Abate by
- Apr 18, 2014
- Penalty
- Initial $2,100 · Current $1,050 Reduced
General-duty citation text
29 CFR 1910.242(b): Compressed air used for cleaning. Compressed air shall not be used for cleaning purposes except where reduced to less than 30 p.s.i. and then only with effective chip guarding and personal protective equipment. a) Compressed air used for cleaning the injection molding machines were not reduced to 30 p.s.i. in that the pressure was in excess of 70 p.s.i.
Recent events (2)
- · I (S) $1050
- · Z (S) $2100
More inspections in this industry (NAICS 326160)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 339561490.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.