JACKSONVILLE, FL ·
OSHA Inspection: AMERICAN TECHNICAL CERAMICS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of AMERICAN TECHNICAL CERAMICS, INC. in 2201 CORPORATE SQUARE BLVD., JACKSONVILLE, FL 32216 (NAICS 334412). OSHA activity number 339581480.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- AMERICAN TECHNICAL CERAMICS, INC.
- Site address
- 2201 CORPORATE SQUARE BLVD.
- City
- JACKSONVILLE
- State
- FL
- ZIP
- 32216
- Mailing
- 2201 CORPORATE SQUARE BLVD., JACKSONVILLE, FL 32216
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 334412
- Employees
- 200
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.219 C02 I
- Issued
- Apr 24, 2014
- Abate by
- Jun 11, 2014
- Penalty
- Initial $6,300 · Current $3,780 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: a. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 2A, the horizontal shafts that support both belt drive wheel rollers were not protected by stationary casings or enclosed sides, exposing employees to caught-in hazards. b. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 2B, the horizontal shafts that support both belt drive wheel rollers were not protected by stationary casings or enclosed sides, exposing employees to caught-in hazards. c. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 3A, the horizontal shafts that support both belt drive wheel rollers were not protected by stationary casings or enclosed sides, exposing employees to caught-in hazards. d. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 3B, the horizontal shafts that support both belt drive wheel rollers were not protected by stationary casings or enclosed sides, exposing employees to caught-in hazards.
Recent events (2)
- · I (S) $3780
- · Z (S) $6300
1910.219 C04 I
- Issued
- Apr 24, 2014
- Abate by
- Jun 11, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(c)(4)(i): Unguarded shaft end(s) projected more than one half the diameter of the shaft: a. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 2A, the north horizontal shaft supporting the conveyor wheel roller was unguarded and projected more than half the diameter of the shaft, exposing employees to caught-in hazards. b. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 2B, the north horizontal shaft supporting the conveyor wheel roller was unguarded and projected more than half the diameter of the shaft, exposing employees to caught-in hazards.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.219 C04 II
- Issued
- Apr 24, 2014
- Abate by
- Jun 11, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(c)(4)(ii): The unused keyway(s) of projecting shaft end(s) were not filled up or covered: a. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 2B, had projecting horizontal shafts that had an unused keyways that was not filled up or covered, exposing employees to caught-in hazards. b. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 3A, had projecting horizontal shafts that had unused keyways that were not filled up or covered, exposing employees to caught-in hazards. c. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 3B, had a projecting horizontal shaft that had unused keyways that were not filled up or covered, exposing employees to caught-in hazards.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.219 I01
- Issued
- Apr 24, 2014
- Abate by
- Jun 11, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(i)(1): Screw(s) or bolt(s) used in revolving collar(s) projected beyond the largest periphery of the collar: a. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 2B, setscrews used in the revolving collars projected beyond the largest periphery of the collar exposing employees to caught-in hazards. b. On or about February 11, 2014, at the ATC Steel Belt Caster Machine, number 3B, setscrews used in the revolving collars projected beyond the largest periphery of the collar exposing employees to caught-in hazards.
Recent events (2)
- · I (S) $0
- · Z (S) $0
More inspections at American Technical Ceramics, INC.
View American Technical Ceramics, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 334412)
More inspections in FL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339581480.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.