SAINT LOUIS, MO —
OSHA Inspection: SWAN INDUSTRIES INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SWAN INDUSTRIES INC. in 10975 LIN-VALLE DRIVE, SAINT LOUIS, MO 63123 (NAICS 333512). OSHA activity number 339583387.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SWAN INDUSTRIES INC.
- Site address
- 10975 LIN-VALLE DRIVE
- City
- SAINT LOUIS
- State
- MO
- ZIP
- 63123
- Mailing
- 10975 LIN-VALLE DRIVE, SAINT LOUIS, MO 63123
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333512
- Employees
- 18
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Feb 14, 2014
- Abate by
- Apr 3, 2014
- Penalty
- Initial $2,000 · Current $0 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employee(s) in that employee(s) were exposed to the hazard of being caught-by: Inside of the Production Area, employees were exposed to an amputation/laceration hazard due to a possible machine process malfunction on the following equipment: a/ Bridgeport Milling Machine, unknown m/n or s/n. b/ Lagun FTV-1 Milling Machine, unknown s/n. c/ Lagun FTV-1 Milling Machine, unknown s/n. d/ Torvino Radial Arm Drilling Machine, m/n TRL 1300, s/n unknown. One method of abatement to correct this apparent hazard is to install emergency stop devices as required by ANSI B11.8-2001, paragraph 6.12.1. DISCLAIMER: a/ The employer is not limited to the abatement method(s) suggested by OSHA. b/ The employer is responsible for selecting and implementing an effective abatement method.
Recent events (3)
- — F (S) $0
- — C (S) $2000
- — Z (S) $2000
1910.212 A01
- Issued
- Feb 14, 2014
- Abate by
- Apr 3, 2014
- Penalty
- Initial $2,000 · Current $2,000
General-duty citation text
29 CFR 1910.212(a)(1): Machine guarding was not provided to protect operator(s) and other employees from hazard(s) created by rotating parts: Inside of the Production Area, the following machines were unguarded: a/ Milltronics Milling Machine, Partner 9, s/n 1887912. b/ Bridgeport Milling Machine, unknown m/n or s/n. c/ Lagun FTV-1 Milling Machine, unknown s/n. d/ Lagun FTV-1 Milling Machine, unknown s/n. e/ Torvino Radial Arm Drilling Machine, m/n TRL 1300, s/n unknown. f/ Vertical Pedestal Sander, unknown make, model, or serial number.
Recent events (1)
- — Z (S) $2000
1910.132 D02
- Issued
- Feb 14, 2014
- Abate by
- Apr 3, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.132(d)(2): The employer did not verify that the required workplace hazard assessment has been performed through a written certification that identifies the workplace evaluated; the person certifying that the evaluation has been performed; the date(s) of the hazard assessment; and, which identifies the document as a certification of hazard assessment: a/ The workplace hazard assessment for personal protective equipment was not certified.
Recent events (1)
- — Z (O) $0
1910.147 C07 IV
- Issued
- Feb 14, 2014
- Abate by
- Apr 3, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(iv): The employer did not certify that employee training has been accomplished and was being kept up to date. The certification did not contain each employee's name and dates of training: a/ Employee training in the lockout/tagout program was not verified by the employer.
Recent events (1)
- — Z (O) $0
1910.303 F02
- Issued
- Feb 14, 2014
- Abate by
- Apr 3, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.303(f)(2): Services, feeders, and branch circuits. Each service, feeder, and branch circuit, at its disconnecting means or over current device, shall be legibly marked to indicate its purpose, unless located and arranged so the purpose is evident. a/ Throughout the Production Area, circuit breaker panel boxes were not legibly marked to indicate voltage.
Recent events (1)
- — Z (O) $0
More inspections at Swan Industries INC.
View Swan Industries INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333512)
More inspections in MO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339583387.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.