OSHA Inspection: SAVAGE PRECISION FABRICATION, INC.

Issued

Jun 12, 2014

Abate by

Jun 24, 2014

Penalty

Initial $2,800 · Current $0 Reduced

General-duty citation text

29 CFR 1910.22(d)(1): In every building or other structure, or part thereof, used for mercantile, business, industrial, or storage purposes, the loads approved by the building official were not marked on plates of approved design which were not supplied and securely affixed by the owner of the building, or his duly authorized agent, in a conspicuous place in each space to which they relate. Such plates are not to be removed or defaced but, if lost, removed, or defaced, were not replaced by the owner or his agent:     This violation was most recently observed on February 12, 2014, at the worksite located at 1415 Martinez Lane, Wylie, Texas; where employees were exposed to crushed- by hazards from falling debris from the collapse of a roof that did not indicate its maximum load capacity.

Issued

Jun 12, 2014

Abate by

Aug 1, 2014

Penalty

Initial $4,900 · Current $2,450 Reduced

General-duty citation text

29 CFR 1910.147(c)(1):  The employer did not establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment was not isolated from the energy source and rendered inoperative:     This violation most was most recently discovered February 12, 2014, at the worksite located at 1415 Martinez Lane, Wylie, Texas; where the employer did not ensure that employees performing maintenance on equipment were trained in the lockout/tagout procedures.

Issued

Jun 12, 2014

Abate by

Jun 24, 2014

Penalty

Initial $4,900 · Current $2,450 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    This violation most was most recently discovered February 12, 2014, at the worksite located at 1415 Martinez Lane, Wylie, Texas; where employees were exposed to amputation hazards while      A.  Operating a drill press with an unguarded bit.

Issued

Jun 12, 2014

Abate by

Aug 1, 2014

Penalty

Initial $4,900 · Current $2,450 Reduced

General-duty citation text

29 CFR 1910.212(a)(3)(ii): The point of operation of machines whose operation exposes an employee to injury, was not guarded. The guarding device was not in conformity with any appropriate standards therefor, or, in the absence of applicable specific standards, was not designed and constructed as to prevent the operator from having any part of his body in the danger zone during the operating cycle:     This violation most was most recently discovered February 12, 2014, at the worksite located at 1415 Martinez Lane, Wylie, Texas; where employees were exposed to amputation hazards while operating a press brake without guards.

Issued

Jun 12, 2014

Abate by

Jun 24, 2014

Penalty

Initial $4,200 · Current $2,100 Reduced

General-duty citation text

29 CFR 1910.215(a)(1): Abrasive wheels were not used only on machines provided with safety guards as defined in the following paragraphs of this section:     This violation most was most recently discovered February 12, 2014, at the worksite located at 1415 Martinez Lane, Wylie, Texas; where employees operated abrasive wheel grinders without the use of a guard.

Issued

Jun 12, 2014

Abate by

Jun 24, 2014

Penalty

Initial $3,500 · Current $1,750 Reduced

General-duty citation text

29 CFR 1910.303(b)(2): Listed or labeled equipment was not installed and used in accordance with any instructions included in the listing or labeling:    This violation most was most recently discovered February 12, 2014, at the worksite located at 1415 Martinez Lane, Wylie, Texas; where employees were using electrical receptacle boxes that are not installed inside of the walls to operate grinders.