ROMEOVILLE, IL ·
OSHA Inspection: ROLL MACHINING TECHNOLOGIES AND SOLUTIONS, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of ROLL MACHINING TECHNOLOGIES AND SOLUTIONS, INC. in 641 FORESTWOOD DRIVE, ROMEOVILLE, IL 60446 (NAICS 332710). OSHA activity number 339726705.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ROLL MACHINING TECHNOLOGIES AND SOLUTIONS, INC.
- Site address
- 641 FORESTWOOD DRIVE
- City
- ROMEOVILLE
- State
- IL
- ZIP
- 60446
- Mailing
- 641 FORESTWOOD DRIVE, ROMEOVILLE, IL 60446
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 30
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.305 B01 I
- Issued
- May 13, 2014
- Abate by
- Aug 12, 2014
- Penalty
- Initial $2,100 · Current $1,470 Reduced
General-duty citation text
29 CFR 1910.305(b)(1)(i): Conductors entering cutout boxes, cabinets, or fittings shall be protected from abrasion, and openings through which conductors enter shall be effectively closed. Production area - On or about April 22, 2014, employees were required to operate various machinery (lathes / mills) powered by conductors not properly protected from abrasion in accordance with OSHA standards, thereby exposing employees to the hazards associated with electricity (electrocution, fire, and arc flash).
Recent events (2)
- · I (S) $1470
- · Z (S) $2100
1910.305 G01 IV A
- Issued
- May 13, 2014
- Abate by
- Aug 12, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.305(g)(1)(iv)(A): Unless specifically permitted otherwise in paragraph (g)(1)(ii) of this section, flexible cords and cable my not be used: (A) As a substitute for the fixed wiring of a structure; Maintenance Shop - On or about April 22, 2014, flexible cords (Extension cords / power strips) were used as a substitute for fixed wiring of a structure on the machine pedestals, thereby exposing employees to electrical fire hazards.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.147 C04 II
- Issued
- May 13, 2014
- Abate by
- Aug 12, 2014
- Penalty
- Initial $4,900 · Current $3,430 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(ii): The procedures shall clearly and specifically outline the scope, purpose, authorization, rules, and techniques to be utilized for the control of hazardous energy, and the means to enforce compliance including, but not limited to, the following: Throughout production area - On or about April 22, 2014, employees were required to clean and / or change / set dies on various machinery (lathes / mills) on a daily basis. The employer's written lockout / tagout program did not include written procedures for the control of hazardous energy where employees were required to clean and/or change / set dies. Employees were thereby exposed to the hazards associated with the unexpected reenergization of equipment.
Recent events (2)
- · I (S) $3430
- · Z (S) $4900
1910.147 D04 I
- Issued
- May 13, 2014
- Abate by
- Aug 12, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices shall be affixed to each energy isolating device by authorized employees. Throughout production area - On or about April 22, 2014, employees were required to clean and/or change / set dies on various machinery (lathes / mills) on a daily basis. The employer did not ensure that employees affixed a lockout / tagout device prior to cleaning and/or changing / setting dies. Employees were thereby exposed to the hazards associated with the unexpected reenergization of equipment.
Recent events (2)
- · I (S) $0
- · Z (S) $0
More inspections at Roll Machining Technologies and Solutions, INC.
View Roll Machining Technologies and Solutions, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339726705.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.