ELK GROVE VILLAGE, IL —
OSHA Inspection: M & R PRECISION MACHINING, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of M & R PRECISION MACHINING, INC. in 680 LIVELY BOULEVARD, ELK GROVE VILLAGE, IL 60007 (NAICS 332710). OSHA activity number 339806598.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- M & R PRECISION MACHINING, INC.
- Site address
- 680 LIVELY BOULEVARD
- City
- ELK GROVE VILLAGE
- State
- IL
- ZIP
- 60007
- Mailing
- 680 LIVELY BOULEVARD, ELK GROVE VILLAGE, IL 60007
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 45
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.23 A07
- Issued
- Oct 28, 2014
- Abate by
- Nov 24, 2014
- Penalty
- Initial $2,100 · Current $1,050 Reduced
General-duty citation text
29 CFR 1910.23(a)(7): Every temporary floor opening did not have standard railings, or was not constantly attended by someone: a) CNC Milling Machine Department-The employer did not ensure that the temporary floor opening near the emergency exit door was guarded by either a standard railing or an attendant.
Recent events (2)
- — I (S) $1050
- — Z (S) $2100
1910.23 C01
- Issued
- Oct 28, 2014
- Abate by
- Nov 24, 2014
- Penalty
- Initial $3,500 · Current $1,750 Reduced
General-duty citation text
29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings (or equivalent) and toeboards:Note: Toeboards are only required when persons can pass, there is moving equipment or there is equipment with which falling materials could create a hazard. a) CNC Milling Machine Department- The employer did not provide standard railing(s) or the equivalent on the mezzanine to prevent from employees falling eight feet to the floor.
Recent events (2)
- — I (S) $1750
- — Z (S) $3500
1910.178 L04 III
- Issued
- Oct 28, 2014
- Penalty
- Initial $2,100 · Current $1,050 Reduced
General-duty citation text
29 CFR 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operator's performance was not being conducted at least once every three years: a) Facility wide- The employer did not perform refresher training, including an evaluation of the effectiveness of that training, to evaluate the operators knowledge and skill to operate the forklift safely at least once every three years for all powered industrial vehicle operators.
Recent events (2)
- — I (S) $1050
- — Z (S) $2100
1910.212 A03 II
- Issued
- Oct 28, 2014
- Abate by
- Nov 24, 2014
- Penalty
- Initial $2,800 · Current $1,400 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): a) CNC Milling Machine Department- CNC milling machines, including the H Plus-405 2620 CNC Milling Machine, did not have an appropriate guarding device, such as an interlock device, to prevent employees from having any part of their body in the danger zone during the operating cycle or to perform tasks, such as cleaning equipment, tool changes, and programmed set ups.
Recent events (2)
- — I (S) $1400
- — Z (S) $2800
1910.305 G01 IV A
- Issued
- Oct 28, 2014
- Abate by
- Nov 24, 2014
- Penalty
- Initial $2,100 · Current $1,050 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv)(A): Flexible cords and/or cables were used as a substitute for the fixed wiring of a structure: a) Facility wide- The employer did not ensure that extension cords were not used as a substitute for fixed wiring. Extension cords were used to supply power to items, such as oil skimmers, other extension cords, power strips, and equipment vending machine.
Recent events (2)
- — I (S) $1050
- — Z (S) $2100
More inspections at M & R Precision Machining, INC.
View M & R Precision Machining, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339806598.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.